Gigaswift ethernet card on reboot Post: 302487060

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such...

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

8. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ?

9. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ...

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

LEARN ABOUT DEBIAN

ne2k-pci-diag

NE2K-PCI-DIAG(8)					      System Manager's Manual						  NE2K-PCI-DIAG(8)

NAME

       ne2k-pci-diag - EEPROM setup and diagnostic program for PCI NE2000 ethernet cards.

SYNOPSIS

       ne2k-pci-diag [options]

DESCRIPTION

       ne2k-pci-diag  is  a  program  that  you  can  use  to  diagnose problems with PCI NE200 Enternet adapters. This include cards with RealTek
       RTL8029AS, Holtak HT80232 ECON-PCI, Winbond W89c940f and VIA VT86C926 (Amazon) chips.

OPTIONS

       These programs follow the usual GNU command line syntax, with long options starting with  two  dashes  (`-').   A  summary  of  options	is
       included below.

       -h, --help
	      Show summary of options.

       -V, --version
	      Show version of program.

       -v, --verbose
	      Verbose mode.

       -q, --quiet
	      Be very unverbose.

       -a, --show_all_registers
	      Print all registers.

       -# <cardnum>
	      Use card number <cardnum>.

       -e, --show-eeprom
	      Dump EEPROM contents to stdout.

       -E, --emergency-rewrite
	      Re-write a corrupted EEPROM.

       -p, --port-base <port>
	      Specify port to use.

       -F, --new-interface <interface>
	      Interface  number.  Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
	      100baseFx-FDX, MII and Autosense.

       -H, --new-hwaddress <address>
	      Set card to a new hardware address.

       -m, --show-mii
	      Dump MII management registers.

       -R, --reset
	      Reset the transceiver.

       -T, --test
	      Do register and SRAM test.

       -w, --write-EEPROM <values>
	      Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!

       -f, --force-detection
	      Try to identify the card, even if it is active.

       -t, --chip-type <card>
	      Explicitly set the chip. To get all valid numbers, run ne2k-pci-diag with the options '-t -1'.

SEE ALSO

       mii-diag(8)

AUTHOR

       ne2k-pci-diag was written and is still maintained by Donald Becker <becker@scyld.com>.  This manual page was  written  by  Alain  Schroeder
       <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).

								 February 18, 2002						  NE2K-PCI-DIAG(8)

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Discussion started by: i2admin

2. IP Networking

RedHat and Ethernet card no like each other

Discussion started by: Minnesota Red

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

Discussion started by: Tony Empire

4. SCO

Issue with a ethernet card

Discussion started by: tazmss1