Sponsored Content
Operating Systems Solaris Gigaswift ethernet card on reboot Post 302486991 by xe2bss on Tuesday 11th of January 2011 05:52:10 AM
Old 01-11-2011
Gigaswift ethernet card on reboot

I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card won't come up, what may be cause and solution to this problem?
Thanks
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

6. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies

9. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ... (1 Reply)
Discussion started by: manni2
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
CARD(1) 								FSF								   CARD(1)

NAME
card - print reference card of program options SYNOPSIS
card [OPTION]... PROGRAM... DESCRIPTION
Print a reference card of the PROGRAMs thanks to their inline help. OPTIONS
-h, --help display this help and exit -v, --version display version information and exit -o, --output=FILE save the output in FILE -l, --language=LL print the help in the language LL (default: English) --command=CMD perform pretty-printing on the output of CMD (e.g. --command='netscape -help') Options for a2ps are given after `--', for instance $ card -lfr a2ps -- -Pdisplay -4 News, updates and documentation: http://www.inf.enst.fr/~demaille/a2ps/ AUTHOR
Written by Akim Demaille. REPORTING BUGS
Report bugs to <bug-a2ps@gnu.org>. COPYRIGHT
Copyright (C) 1997-99 Akim Demaille, Miguel Santana This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. SEE ALSO
a2ps(1), card(1), fixps(1), pdiff(1), psset(1), texi2dvi4a2ps(1). The full documentation for card is maintained as a Texinfo manual. If the info and card programs are properly installed at your site, the command info card should give you access to the complete manual. card 1.3 (GNU a2ps 4.14) March 2014 CARD(1)
All times are GMT -4. The time now is 11:06 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy