|
|
Sponsored Content
Operating Systems
Solaris
Packet loss on ce interface.
Post 302485977 by mtomar on Thursday 6th of January 2011 03:22:49 PM
01-06-2011
I have seen this problem when interface choose a lower duplex setting. Generally i use this simple trick.
1. enable auto neg with all options enabled
2. disable all capabilities except adv_1000fdx_cap.
This will make interface run auto-neg but it will not negotiate anything below 1000Full.
I have more than 10 machines running like this. no issue since past 9 months
.
Just make sure to add a start up script to make these changes available after reboot. or if you are comfortable you can edit /etc/system file.
Hope it helps.
1. enable auto neg with all options enabled
2. disable all capabilities except adv_1000fdx_cap.
This will make interface run auto-neg but it will not negotiate anything below 1000Full.
I have more than 10 machines running like this. no issue since past 9 months
.Just make sure to add a start up script to make these changes available after reboot. or if you are comfortable you can edit /etc/system file.
Hope it helps.
This User Gave Thanks to mtomar For This Post:
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I am experiencing a problem where under a dial condition I am experiencing packet loss, which is failrly normal, but the response to the packet loss is taking bewteen 6 and 10 seconds. Could someone please advise what the industry standard is on the response time under a packet loss senario. (1 Reply)
Discussion started by: shane
1 Replies
2. IP Networking
I have 4 network ports on our T5240 sun server.
all but 1 gives packet losses (nxge1)
nxge0 gives on average 50% packet loss, very bad.
nxge2 gives on average 1-2% packet loss.
nxge3 gives on average 20% packet loss.
Is there a tool or something to help me find the problem? (11 Replies)
Discussion started by: photon
11 Replies
3. HP-UX
Hello,
I'm writing to you because I encountered the following problem. My program displayes all network interfaces that are available in the system, but I would like to add a functionality in which a user can enter a destination address IP (ex. the IP address of the Google search engine) and will... (1 Reply)
Discussion started by: foxrafi
1 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. AIX
(5 Replies)
Discussion started by: Vishal_dba
5 Replies
9. IP Networking
RHEL 7.0, IPV6
Scenario:
I have routed specific network using network scripts.
1. "ip -6 route show" shows that route has been added. ( with metric 1024)
2. Ping of the specific IP through that route is successful.
3. Now after few days, for some reason, we see that cache route appears for... (3 Replies)
Discussion started by: msr1981
3 Replies
LEARN ABOUT LINUX
ifplugd.conf
ifplugd.conf(5) File Formats Manual ifplugd.conf(5) NAME
ifplugd.conf - ifplugd configuration file SYNOPSIS
/etc/default/ifplugd DESCRIPTION
ifplugd.conf is the configuration file for ifplugd. It is a shell script that is sourced by the init script starting the daemon. It shall be used to set environment variables which are interpreted by the init script: OPTIONS
INTERFACES Specifies the ethernet interfaces to monitor. It has to contain a space seperated list of network interfaces names. Most users will probably use "eth0" here, however you may add additional interfaces for monitoring more than one device. A special value is sup- ported as well: "auto" will enable a more or less working auto detection of available network devices. This won't make you happy when using network module auto loading, since it cannot detect currently unloaded network devices. HOTPLUG_INTERFACES Specifies the interfaces that can be hotplugged (like interfaces on PCMCIA, USB or WLAN adapters). "all" can be used to make the udev script start an ifplugd process for any hotplugged interfaces (except those already listed in INTERFACES). ARGS Additional command line arguments for ifplugd invocation. See ifplugd(8) for further information. ARGS_iface If specified for an interface this variable takes precedence over ARGS. This may be useful if more than one network device is present. SEE ALSO
ifplugd(8) COMMENTS
This man page was written using xmltoman(1) by Oliver Kurth. Manuals User ifplugd.conf(5)