01-05-2011
have you patched the machine with some newer patch cluster? i remember some problems with ce interfaces which are fixed by patches... also check the cabel and the switch port settings... if this is a new problem and not something that was always there, a hardware problem might be more likely.
This User Gave Thanks to DukeNuke2 For This Post:
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I am experiencing a problem where under a dial condition I am experiencing packet loss, which is failrly normal, but the response to the packet loss is taking bewteen 6 and 10 seconds. Could someone please advise what the industry standard is on the response time under a packet loss senario. (1 Reply)
Discussion started by: shane
1 Replies
2. IP Networking
I have 4 network ports on our T5240 sun server.
all but 1 gives packet losses (nxge1)
nxge0 gives on average 50% packet loss, very bad.
nxge2 gives on average 1-2% packet loss.
nxge3 gives on average 20% packet loss.
Is there a tool or something to help me find the problem? (11 Replies)
Discussion started by: photon
11 Replies
3. HP-UX
Hello,
I'm writing to you because I encountered the following problem. My program displayes all network interfaces that are available in the system, but I would like to add a functionality in which a user can enter a destination address IP (ex. the IP address of the Google search engine) and will... (1 Reply)
Discussion started by: foxrafi
1 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. AIX
(5 Replies)
Discussion started by: Vishal_dba
5 Replies
9. IP Networking
RHEL 7.0, IPV6
Scenario:
I have routed specific network using network scripts.
1. "ip -6 route show" shows that route has been added. ( with metric 1024)
2. Ping of the specific IP through that route is successful.
3. Now after few days, for some reason, we see that cache route appears for... (3 Replies)
Discussion started by: msr1981
3 Replies
LEARN ABOUT DEBIAN
stg-series
STG-SERIES(1) StGit Manual STG-SERIES(1)
NAME
stg-series - Print the patch series
SYNOPSIS
stg series [options] [<patch-range>]
DESCRIPTION
Show all the patches in the series, or just those in the given range, ordered from top to bottom.
The applied patches are prefixed with a + (except the current patch, which is prefixed with a >), the unapplied patches with a -, and the
hidden patches with a !.
Empty patches are prefixed with a 0.
OPTIONS
-b BRANCH, --branch BRANCH
Use BRANCH instead of the default branch.
-a, --all
Show all patches, including the hidden ones.
-A, --applied
Show the applied patches only.
-U, --unapplied
Show the unapplied patches only.
-H, --hidden
Show the hidden patches only.
-m BRANCH, --missing BRANCH
Show patches in BRANCH missing in current.
-c, --count
Print the number of patches in the series.
-d, --description
Show a short description for each patch.
--author
Show the author name for each patch.
-e, --empty
Before the +, >, -, and ! prefixes, print a column that contains either 0 (for empty patches) or a space (for non-empty patches).
--showbranch
Append the branch name to the listed patches.
--noprefix
Do not show the patch status prefix.
-s, --short
List just the patches around the topmost patch.
STGIT
Part of the StGit suite - see linkman:stg[1]
StGit 03/13/2012 STG-SERIES(1)