Packet loss on ce interface. Post: 302485423

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Response time under packet loss

I am experiencing a problem where under a dial condition I am experiencing packet loss, which is failrly normal, but the response to the packet loss is taking bewteen 6 and 10 seconds. Could someone please advise what the industry standard is on the response time under a packet loss senario.

2. IP Networking

packet loss problem

I have 4 network ports on our T5240 sun server. all but 1 gives packet losses (nxge1) nxge0 gives on average 50% packet loss, very bad. nxge2 gives on average 1-2% packet loss. nxge3 gives on average 20% packet loss. Is there a tool or something to help me find the problem?

3. HP-UX

How to determine network interface that will be used to send a packet for an IP

Hello, I'm writing to you because I encountered the following problem. My program displayes all network interfaces that are available in the system, but I would like to add a functionality in which a user can enter a destination address IP (ex. the IP address of the Google search engine) and will...

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

8. AIX

Packet loss coming with big packet size ping

9. IP Networking

Packet going out of wrong interface due to OS automatically added cache route with lower metric

RHEL 7.0, IPV6 Scenario: I have routed specific network using network scripts. 1. "ip -6 route show" shows that route has been added. ( with metric 1024) 2. Ping of the specific IP through that route is successful. 3. Now after few days, for some reason, we see that cache route appears for...

LEARN ABOUT DEBIAN

rds-ping

RDS-PING(1)						    BSD General Commands Manual 					       RDS-PING(1)

NAME

     rds-ping -- test reachability of remote node over RDS

SYNOPSIS

     rds-ping [-c count] [-i interval] [-I local_addr] remote_addr

DESCRIPTION

     rds-ping is used to test whether a remote node is reachable over RDS.  Its interface is designed to operate pretty much the standard ping(8)
     utility, even though the way it works is pretty different.

     rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is
     bound; instead, the kernel processes incoming packets and responds to them.

OPTIONS

     The following options are available for use on the command line:

     -c count
	     Causes rds-ping to exit after sending (and receiving) the specified number of packets.

     -I address
	     By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address
	     (i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source
	     address).	Using the -I option, you can override this choice.

     -i timeout
	     By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout
	     value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds
	     or microseconds, respectively.
     Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results.

AUTHORS

     rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>.

SEE ALSO

     rds(7), rds-info(1), rds-stress(1).

BSD
								   Apr 22, 2008 							       BSD