01-03-2011
Thanks for the information!
The only problem that I see now is that I dont have any PC that has serial port, I have a PC with quad processor 4GB RAM and Vista is running so not sure if it can simulate the triggers if I use USB to Serial convertor.
10 More Discussions You Might Find Interesting
1. Solaris
hi,
i hv received SUNfire 280R system ........for its initial configuration i want to connect to it through hyperterminal from the windows system..........i hv got one serial port to RJ-45 port converter with the system............can anybody tell me the normal console cable which is used to... (3 Replies)
Discussion started by: girish_shukla
3 Replies
2. Solaris
hi!!!!!!
how to upgrade sunfire 280R server from solaris8 to solaris9?
pls help me.
Thanks & Regards
-Vishal (1 Reply)
Discussion started by: Vishal Shroff
1 Replies
3. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
4. Solaris
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Discussion started by: hcclnoodles
4 Replies
5. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
6. Solaris
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
Discussion started by: lamoul
3 Replies
7. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
8. Solaris
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Discussion started by: lamoul
2 Replies
9. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
10. Hardware
Hi,
I'm a newbie in the Unix world... :confused:
I own a Sun Sunfire 280R computer with one 750Mhz CPU. I ordered two CPU of 900Mhz to replace it; however in the Service manual from Sun I read that to use 900Mhz CPU i will need to have a OBP of at least version 4.5.16. When I type .version in... (2 Replies)
Discussion started by: Monkey114
2 Replies
UPLCOM(4) BSD Kernel Interfaces Manual UPLCOM(4)
NAME
uplcom -- USB support for Prolific PL-2303/2303X/2303HX serial adapters driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device uplcom
device ucom
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
uplcom_load="YES"
DESCRIPTION
The uplcom driver provides support for various serial adapters based on the Prolific PL-2303, PL-2303X and PL-2303HX USB-to-RS232 Bridge
chips.
The device is accessed through the ucom(4) driver which makes it behave like a tty(4).
HARDWARE
The uplcom driver supports the following adapters:
o ATEN UC-232A
o BAFO BF-800
o BAFO BF-810
o Belkin F5U257
o ELECOM UC-SGT
o HAL Corporation Crossam2+USB IR commander
o Hama USB RS-232 Serial Adapter
o Hamlet exagerate XURS232
o IOGEAR UC-232A
o I/O DATA USB-RSAQ
o I/O DATA USB-RSAQ2
o I/O DATA USB-RSAQ3
o Mobile Action MA-620 Infrared Adapter
o PLANEX USB-RS232 URS-03
o RATOC REX-USB60
o Radio Shack USB Serial Cable
o Sandberg USB to Serial Link (model number 133-08)
o SOURCENEXT KeikaiDenwa 8 (with and without charger)
o Sony Ericsson USB Cable (Susteen USB Data Cable)
o Willcom W-SIM DD PHS terminal.(WS002IN)
SEE ALSO
tty(4), ucom(4), usb(4)
HISTORY
The uplcom driver appeared in NetBSD 1.6. This manual page was adopted from NetBSD by Tom Rhodes <trhodes@FreeBSD.org> in April 2002.
BSD
November 22, 2006 BSD