01-03-2011
Try connecting a PC's serial port to ttya on the back of the 280R. Start Hyperterm (or some other serial comm app) and select com1 on your PC. Then cold-cycle the 280R and see what you get.
HTH
10 More Discussions You Might Find Interesting
1. Solaris
hi,
i hv received SUNfire 280R system ........for its initial configuration i want to connect to it through hyperterminal from the windows system..........i hv got one serial port to RJ-45 port converter with the system............can anybody tell me the normal console cable which is used to... (3 Replies)
Discussion started by: girish_shukla
3 Replies
2. Solaris
hi!!!!!!
how to upgrade sunfire 280R server from solaris8 to solaris9?
pls help me.
Thanks & Regards
-Vishal (1 Reply)
Discussion started by: Vishal Shroff
1 Replies
3. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
4. Solaris
Hi there
Does anybody know what the biggest capacity disk I can get into a Sunfire 280R
I currently have two 73gb disks , but I need to get these up to the biggest available
Any help would be greatly appreciated (4 Replies)
Discussion started by: hcclnoodles
4 Replies
5. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
6. Solaris
Hi,
I have to question:
1) when O/S is booting, i see messages:
/dev/rdsk/c1t0d0s5: is logging
/dev/rdsk/c1t0d0s3: is logging
/dev/rdsk/c1t0d0s7: is logging
i partitioned these slices during installation of O/S 5.9. I can access to these mountpoint no problem. But... (3 Replies)
Discussion started by: lamoul
3 Replies
7. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
8. Solaris
Hi,
i just finished installing solaris 5.9 and I'm looking for the tools to tell me if i should update the patches or how to make sure that the current patches are ok?
thanks (2 Replies)
Discussion started by: lamoul
2 Replies
9. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
10. Hardware
Hi,
I'm a newbie in the Unix world... :confused:
I own a Sun Sunfire 280R computer with one 750Mhz CPU. I ordered two CPU of 900Mhz to replace it; however in the Service manual from Sun I read that to use 900Mhz CPU i will need to have a OBP of at least version 4.5.16. When I type .version in... (2 Replies)
Discussion started by: Monkey114
2 Replies
LEARN ABOUT DEBIAN
hpialarms
hpialarms(1) OpenHPI hpialarms(1)
NAME
hpialarms - A openhpi sample application that shows "Alarm Control" management instruments
SYNOPSIS
hpialarms [-a -b -c -i -m -n -p -o -x]
DESCRIPTION
hpialarms walks the RPT (Resource Present Table) for resouces that have "Alarm Control" management instruments (SAHPI_CTRL_LED).
OPTIONS
-c1 sets Critical Alarm on
-c0 sets Critical Alarm off
-m1 sets Major Alarm on
-m0 sets Major Alarm off
-n1 sets Minor Alarm on
-n0 sets Minor Alarm off
-p1 sets Power Alarm on
-p0 sets Power Alarm off
-i5 sets Chassis ID on for 5 sec
-i0 sets Chassis ID off
-a1 sets Disk A fault on
-a0 sets Disk A fault off
-b1 sets Disk B fault on
-b0 sets Disk B fault off
-d[byte] sets raw Alarm byte
-o sets all Alarms off
-x show eXtra debug messages
SAMPLE OUTPUT
hpialarmpanel ver 0.6
RptInfo: UpdateCount = 5, UpdateTime = 8a2dc6c0
rptentry[0] resourceid=1 tag: Mullins
RDR[45]: ctltype=2:1 oem=0 Chassis Identify Control
RDR[48]: ctltype=0:1 oem=10 Front Panel Power Alarm LED state = off
RDR[51]: ctltype=0:1 oem=13 Front Panel Minor Alarm LED state = ON
RDR[46]: ctltype=0:0 oem=0 Cold Reset Control
RDR[49]: ctltype=0:1 oem=11 Front Panel Critical Alarm LED state = off
RDR[50]: ctltype=0:1 oem=12 Front Panel Major Alarm LED state = off
SEE ALSO
AUTHORS
Authors of this man page:
Peter D Phan (pdphan@users.sourceforge.net)
2.14.1 2009-11-23 hpialarms(1)