I have to cd into /sbin in order to use ifconfig to check out my network cards. This has only started to happen since I downloaded the last update from RedHat(The machine runs RedHat 8.0).
Does anyone know what happened?
More importantly, are there any sources that can help me with this... (3 Replies)
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
hey,
I know that ifconfig on linux systems is identical to win ipconfig.
I wanted to know if there is a linux distribution (new or old) that uses the ipconfig command.
thanks alot :) (2 Replies)
hi,
i want to know how to grep inet address for below
below is the output of ifconfig command
/home/JA> ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:0A:5B:2E:E9
inet addr:161.239.203.18 Bcast:161.239.203.127 Mask:255.255.255.128
UP BROADCAST RUNNING... (3 Replies)
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Hi all,
I am getting some error messages during bootup
ifconfig :<hostname> bad address
and some more messages related to it.
I some how checked the /etc/hostanem.hme0 /etc/hosts file.
Entries in these files were proper.
If I am running the following command from root:
... (5 Replies)
Hi there,
I need your help in understanding the below Solaris 10 ifconfig output;
athnetspns02>ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0:... (2 Replies)
So, I have this script that makes a call to ifconfig to pull the interface information and report it. When I log on to the machine the script works just fine. But, if I'm on a remote machine and I make a call like this.
ssh user@server ./script.bash
I get an error saying that the IFCONFIG command... (9 Replies)
Discussion started by: Binary Buddha
9 Replies
LEARN ABOUT NETBSD
iy
IY(4) BSD Kernel Interfaces Manual IY(4)NAME
iy -- Intel EtherExpress PRO/10 Ethernet driver (Intel i82595)
SYNOPSIS
iy0 at isa? port {port} irq ?
DESCRIPTION
The iy device driver supports the EtherExpress PRO/10 card, and might support other ISA cards using the same chip.
MEDIA SELECTION
The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors. Supported media include:
AUI/DIX Standard 15 pin connector
10Base2 BNC, also known as thin-net
10BaseT UTP, also known as twisted pair
The default port to use is the port the card autodetects at ifconfig up time. To choose an alternative port, an explicit medium can be spec-
ified to ifconfig(8) or in your ifconfig.iy? file.
NOTES
The EtherExpress PRO card has no jumpers to set the address. Intel supplies software to set the address of the card in software. You have
to hardwire this address in your kernel configuration file.
SEE ALSO ed(4), eg(4), el(4), ep(4), intro(4), ix(4), le(4), ifconfig(8)STANDARDS
are great. There's so many to choose from.
BSD May 22, 1996 BSD