You should leave eth0 as is: dynamic IP with NAT.
You should add/configure another Network Adapter on the VM that
uses the new host only network: go to the settings of the VM:
Hi Linux gurus,
My boss had asked me to setup a box consisting of this 3 OS (CentOS, Fedora, RedHat) for autopatching. So, whenever there is new patches for CentOS from the internet, this box will grab it, implement it, if tested ok and approved, the patches will then be push to Production... (23 Replies)
Does anyone know if you can use a virtual box image on different O/S's and be able to move it from one server to another of different O/S if needed? (1 Reply)
I am trying to create a new virtual machine (Red Hat) but I am getting the following error
I am completely new to VB and I am probably missing something.
Any help will be greatly appreciated. (4 Replies)
Hi all,
I'm in a pretty messed-up situation, hope you can give me a hand.
I deleted by accident a folder containing a VMware server virtual machine, that contains most critical information. The host OS is CentOS 5.5, which I believe by default uses Ext3.
I shut down the PC intermediately... (2 Replies)
hi
Am Using Windows vista machine where i installed Sun Virtual Box on Which i installled Solaris 10.. am not able to ping my windows machine from Sun OS neither viceversa.. Can someone help me out to get this sorted please .... (2 Replies)
Hello,
Can someone suggest me what I missing, I re-sized a root virtual disk to 30GB on the CentOS VM. After re-sizing the disk, I booted the OS and ran fdisk -list command I was able view the size of the disk as 30GB.
Paritions in the vm before I resize are:
/boot - Primary parition
/... (1 Reply)
Trying to set or modify the randomly set hostID of a Solaris 10 virtual/guest machine that I installed on a Windows-XP host machine (using Virtual Box 4.1.12).
I was able to set/modify the hostname of the Solaris 10 virtual/guest machine during installation as well as via the Virtual Box... (4 Replies)
Hello,
I have two virtual machines ubuntu on virtual box vm1 and vm2 , i'd like to use ssh to connect from vm1 to vm2, please what's the configuration should do?
Thank you (1 Reply)
HI,
I have a Centos linux box and there is interface connect to internet.
I stop the iptables in this box .
After a few day , I find the linux box have been hacked and install some perl script into the box .
Could anyone tell me how the hacker can login into the centos box without knowing... (1 Reply)
Discussion started by: chuikingman
1 Replies
LEARN ABOUT BSD
hy
HY(4) Kernel Interfaces Manual HY(4)NAME
hy - Network Systems Hyperchannel interface
SYNOPSIS
/sys/conf/SYSTEM:
NHY hy_controllers # Hyperchannel
DESCRIPTION
The hy interface provides access to a Network Systems Corporation Hyperchannel Adapter.
The network to which the interface is attached is specified at boot time with an SIOCSIFADDR ioctl. The host's address is discovered by
reading the adapter status register. The interface will not transmit or receive packets until the network number is known.
DIAGNOSTICS
hy%d: unit number 0x%x port %d type %x microcode level 0x%x. Identifies the device during autoconfiguration.
hy%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
hy%d: can't initialize. The interface was unable to allocate UNIBUS resources. This is usually due to having too many network devices on
an 11/750 where there are only 3 buffered data paths.
hy%d: NEX - Non Existent Memory. Non existent memory error returned from hardware.
hy%d: BAR overflow. Bus address register overflow error returned from hardware.
hy%d: Power Off bit set, trying to reset. Adapter has lost power, driver will reset the bit and see if power is still out in the adapter.
hy%d: Power Off Error, network shutdown. Power was really off in the adapter, network connections are dropped. Software does not shut
down the network unless power has been off for a while.
hy%d: RECVD MP > MPSIZE (%d). A message proper was received that is too big. Probable a driver bug. Shouldn't happen.
hy%d: xmit error - len > hy_olen [%d > %d]. Probable driver error. Shouldn't happen.
hy%d: DRIVER BUG - INVALID STATE %d. The driver state machine reached a non-existent state. Definite driver bug.
hy%d: watchdog timer expired. A command in the adapter has taken too long to complete. Driver will abort and retry the command.
hy%d: adapter power restored. Software was able to reset the power off bit, indicating that the power has been restored.
SEE ALSO intro(4N), inet(4F)BUGS
If the adapter does not respond to the status command issued during autoconfigure, the adapter is assumed down. A reboot is required to
recognize it.
The adapter power fail interrupt seems to occur sporadically when power has, in fact, not failed. The driver will believe that power has
failed only if it can not reset the power fail latch after a ``reasonable'' time interval. These seem to appear about 2-4 times a day on
some machines. There seems to be no correlation with adapter rev level, number of ports used etc. and whether a machine will get these
``bogus powerfails''. They don't seem to cause any real problems so they have been ignored.
3rd Berkeley Distribution August 20, 1987 HY(4)