Hi,
I have a file which has special characters. I can't see them when I "vi" the file. But I am sure there are some special un seen characters. How can I see them?
Please help.
Thx (6 Replies)
how do i unescape special characters in Unix.
Suppose i've a file named -xyz.txt, how do I remove the file.
Ofcourse Icant give rm -xyz.txt thats not gonna work.
We can go in regular expression like this ls | grep -e '-'xyz.txt | rm; but I'd like to know any simpler way than this.
Thanks... (3 Replies)
When I open a file in vi, I see the following characters:
\302\240
Can someone explain what these characters mean. Is it ASCII format? I need to trim those characters from a file.
I am doing the following:
tr -d '\302\240'
---------- Post updated at 08:35 PM ---------- Previous... (1 Reply)
Hello All
Seeking the right one SED command.
My attempt is:
From orginal.txt by SED to target.txt
sed -i "/('outbound-callerid/a\$ext->add($context, $exten, '', new ext_SipAddHeader('P-Preferred-Identity', '<sip:${CALLERID(nummer)}@carrier.com>'));" orginal.txtWhat am make wrong?:wall:
... (5 Replies)
I have a line ending with special character and 0
The special character is the field separator for this line
in VI mode the file will look like below, but while cat the special character wont display
i know the hexa code for the special character ^_ is \x1f and ascii code is
\0037,
... (0 Replies)
Need Help For GREP
I have a file say g1.txt and content of file is below
REG ADD "HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer" /v NoDrives /t REG_DWORD /d 4 /f ,
REG ADD "HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer" /v NoClose /t REG_DWORD /d 1 /f ,... (4 Replies)
i need to replace the any special characters with escape characters like below.
test!=123-> test\!\=123
!@#$%^&*()-= to be replaced by
\!\@\#\$\%\^\&\*\(\)\-\= (8 Replies)
grep -i "$line,$opline" COMBO_JUNK|awk -F, '
{
C4+=$4
}
{
}
END {
print C4
}
' OFS=,`
when i run this command in the script.... it o/p all the value as 0 if $line contains any special parameters.....
but the same script if i run in command prompt... it shows... (4 Replies)
Discussion started by: nikhil jain
4 Replies
LEARN ABOUT MOJAVE
cat
CAT(1) BSD General Commands Manual CAT(1)NAME
cat -- concatenate and print files
SYNOPSIS
cat [-benstuv] [file ...]
DESCRIPTION
The cat utility reads files sequentially, writing them to the standard output. The file operands are processed in command-line order. If
file is a single dash ('-') or absent, cat reads from the standard input. If file is a UNIX domain socket, cat connects to it and then reads
it until EOF. This complements the UNIX domain binding capability available in inetd(8).
The options are as follows:
-b Number the non-blank output lines, starting at 1.
-e Display non-printing characters (see the -v option), and display a dollar sign ('$') at the end of each line.
-n Number the output lines, starting at 1.
-s Squeeze multiple adjacent empty lines, causing the output to be single spaced.
-t Display non-printing characters (see the -v option), and display tab characters as '^I'.
-u Disable output buffering.
-v Display non-printing characters so they are visible. Control characters print as '^X' for control-X; the delete character (octal
0177) prints as '^?'. Non-ASCII characters (with the high bit set) are printed as 'M-' (for meta) followed by the character for the
low 7 bits.
EXIT STATUS
The cat utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
The command:
cat file1
will print the contents of file1 to the standard output.
The command:
cat file1 file2 > file3
will sequentially print the contents of file1 and file2 to the file file3, truncating file3 if it already exists. See the manual page for
your shell (i.e., sh(1)) for more information on redirection.
The command:
cat file1 - file2 - file3
will print the contents of file1, print data it receives from the standard input until it receives an EOF ('^D') character, print the con-
tents of file2, read and output contents of the standard input again, then finally output the contents of file3. Note that if the standard
input referred to a file, the second dash on the command-line would have no effect, since the entire contents of the file would have already
been read and printed by cat when it encountered the first '-' operand.
SEE ALSO head(1), more(1), pr(1), sh(1), tail(1), vis(1), zcat(1), setbuf(3)
Rob Pike, "UNIX Style, or cat -v Considered Harmful", USENIX Summer Conference Proceedings, 1983.
STANDARDS
The cat utility is compliant with the IEEE Std 1003.2-1992 (``POSIX.2'') specification.
The flags [-benstv] are extensions to the specification.
HISTORY
A cat utility appeared in Version 1 AT&T UNIX. Dennis Ritchie designed and wrote the first man page. It appears to have been cat(1).
BUGS
Because of the shell language mechanism used to perform output redirection, the command ``cat file1 file2 > file1'' will cause the original
data in file1 to be destroyed!
The cat utility does not recognize multibyte characters when the -t or -v option is in effect.
BSD March 21, 2004 BSD