Hi,
I have a file which has special characters. I can't see them when I "vi" the file. But I am sure there are some special un seen characters. How can I see them?
Please help.
Thx (6 Replies)
how do i unescape special characters in Unix.
Suppose i've a file named -xyz.txt, how do I remove the file.
Ofcourse Icant give rm -xyz.txt thats not gonna work.
We can go in regular expression like this ls | grep -e '-'xyz.txt | rm; but I'd like to know any simpler way than this.
Thanks... (3 Replies)
When I open a file in vi, I see the following characters:
\302\240
Can someone explain what these characters mean. Is it ASCII format? I need to trim those characters from a file.
I am doing the following:
tr -d '\302\240'
---------- Post updated at 08:35 PM ---------- Previous... (1 Reply)
Hello All
Seeking the right one SED command.
My attempt is:
From orginal.txt by SED to target.txt
sed -i "/('outbound-callerid/a\$ext->add($context, $exten, '', new ext_SipAddHeader('P-Preferred-Identity', '<sip:${CALLERID(nummer)}@carrier.com>'));" orginal.txtWhat am make wrong?:wall:
... (5 Replies)
I have a line ending with special character and 0
The special character is the field separator for this line
in VI mode the file will look like below, but while cat the special character wont display
i know the hexa code for the special character ^_ is \x1f and ascii code is
\0037,
... (0 Replies)
Need Help For GREP
I have a file say g1.txt and content of file is below
REG ADD "HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer" /v NoDrives /t REG_DWORD /d 4 /f ,
REG ADD "HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer" /v NoClose /t REG_DWORD /d 1 /f ,... (4 Replies)
i need to replace the any special characters with escape characters like below.
test!=123-> test\!\=123
!@#$%^&*()-= to be replaced by
\!\@\#\$\%\^\&\*\(\)\-\= (8 Replies)
grep -i "$line,$opline" COMBO_JUNK|awk -F, '
{
C4+=$4
}
{
}
END {
print C4
}
' OFS=,`
when i run this command in the script.... it o/p all the value as 0 if $line contains any special parameters.....
but the same script if i run in command prompt... it shows... (4 Replies)
Discussion started by: nikhil jain
4 Replies
LEARN ABOUT V7
tr
TR(1) General Commands Manual TR(1)NAME
tr - translate characters
SYNOPSIS
tr [ -cds ] [ string1 [ string2 ] ]
DESCRIPTION
Tr copies the standard input to the standard output with substitution or deletion of selected characters. Input characters found in
string1 are mapped into the corresponding characters of string2. When string2 is short it is padded to the length of string1 by duplicat-
ing its last character. Any combination of the options -cds may be used: -c complements the set of characters in string1 with respect to
the universe of characters whose ASCII codes are 01 through 0377 octal; -d deletes all input characters in string1; -s squeezes all strings
of repeated output characters that are in string2 to single characters.
In either string the notation a-b means a range of characters from a to b in increasing ASCII order. The character `' followed by 1, 2 or
3 octal digits stands for the character whose ASCII code is given by those digits. A `' followed by any other character stands for that
character.
The following example creates a list of all the words in `file1' one per line in `file2', where a word is taken to be a maximal string of
alphabetics. The second string is quoted to protect `' from the Shell. 012 is the ASCII code for newline.
tr -cs A-Za-z '