12-21-2010
you have to configure and run bind if you wish to do nslookup. hostname in file can be cross checked by doing a ping / telnet etc etc. nslookup will try to get it via dns db file not file(/etc/hosts)
ping dummy.set.com
telnet dummy.set.com
ftp dummy.set.com
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello,
I just got done setting up a DNS server and a client. However, when I do an nslookup with just the hostname, I got this output:
Microsoft Windows 2000
(C) Copyright 1985-2000 Microsoft Corp.
C:\Documents and Settings\dev9>nslookup dev9
Server: webdev.testsurgemail.com
Address:... (3 Replies)
Discussion started by: xnightcrawl
3 Replies
2. Solaris
hey guys, how to add soalris box as a microsoft DNS Client ?
and how to register in the microsoft DNS ??
i managed to query from the DNS server after adding /etc/resolve.conf and editing /etc/nsswitch.conf
but i need to register the soalris server (dns Client) into Microsoft DNS automatically.... (3 Replies)
Discussion started by: mduweik
3 Replies
3. IP Networking
The Linux resolver queries all nameservers in the order they are listed in /etc/resolver.conf.
If a nameserver times out, it advances on to the following nameserver.
But, if a nameserver returns "not found" (NXDOMAIN) it stops.
This behaviour is problematic when you need to resolve names from... (0 Replies)
Discussion started by: colemar
0 Replies
4. Debian
Hi,
I have my router (192.168.1.1) connected to the internet.
I have installed Debian on a server with Bind9 (192.168.1.254).
The configurations files are :
$ cat /etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface... (1 Reply)
Discussion started by: Thibault
1 Replies
5. IP Networking
Is there a way for a server to determine client's DNS ip? I have an application that logs client's IP but in certain cases its desirable to know their DNS too (1 Reply)
Discussion started by: vickylife
1 Replies
6. Linux
Hi all,
What is the procedure to add a client to a DNS server.
what are the settings and files need to be added/changed ?
thanks in advance! (6 Replies)
Discussion started by: lramsb4u
6 Replies
7. Red Hat
Hi Team
we have created a DNS server at RHEL6.2 environment in 10.20.203.x/24 network.
Everything is going well on linux client as nslookup, ping by host etc in entire subnet. We are getting problem in windows client as nslookup working as well but not ping. all the firewall is disabled and... (5 Replies)
Discussion started by: boby.kumar
5 Replies
8. Solaris
Hi all,
I always thought DNS server = provide DNS response (host to ip / ip to host) to DNS client (which send DNS resolve request).
So in my solaris 10 box, i setup /etc/resolv/conf, /etc/nsswitch.conf (added in dns) etc.
Yes, i am able to dig and nslookup. But.. am i a DNS client ?
... (5 Replies)
Discussion started by: javanoob
5 Replies
9. Solaris
Hi,
We have built a new server (RHEL VM)and added that IP/hostname into dns zone configs file on DNS server (Solaris 10). Reloaded the configuration using
and added nameserver into resolv.conf on client. But when I am trying nslookup, its not getting resolved. The nameserver is not able to... (8 Replies)
Discussion started by: snchaudhari2
8 Replies
LEARN ABOUT OPENDARWIN
bootparams
BOOTPARAMS(5) BSD File Formats Manual BOOTPARAMS(5)
NAME
bootparams -- boot parameter database
SYNOPSIS
/etc/bootparams
DESCRIPTION
The bootparams file specifies the boot parameters that diskless clients may request when booting over the network. Each client supported by
this server must have an entry in the bootparams file containing the pathnames for its root and (optionally) swap areas.
Each line in the file (other than comment lines that begin with a #) specifies the client name followed by the pathnames that the client may
request by their logical names. The components of the line are delimited with blank or tab, and may be continued onto multiple lines with a
backslash.
For example:
dummy root=host:/export/dummy/root
swap=host:/export/dummy/swap
dump=host:/export/dummy/swap
When the client named "dummy" requests the pathname for its logical "root" it will be given the pathname ``host:/export/dummy/root'' as the
response to its RPC request. The "host:" component must be supplied.
FILES
/etc/bootparams default configuration file
SEE ALSO
bootparamd(8)
Linux NetKit (0.17) October 2, 1994 Linux NetKit (0.17)