My cutomer wants to set up a OS/apps server with two 72GB drives
configured with RAID 1+0. The way I understand RAID 1+0 is
that if there was a drive failure the whole OS/apps is lost because you
actually need at least 4 drives to set up a RAID 1+0 by splitting
them up into two arrays. Am I... (4 Replies)
hai everybody n good morning........here r some queries.......
1. what is the interlace value in RAID 0 (striping.......)
2. How many no of metadevices are required for mirroring and why......... (1 Reply)
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT LINUX
iir
IIR(4) BSD Kernel Interfaces Manual IIR(4)NAME
iir -- Intel Integrated RAID controller and ICP Vortex driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device scbus
device iir
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
iir_load="YES"
DESCRIPTION
The iir driver claims to interface with the Intel integrated RAID controller cards, and all versions of the ICP Vortex controllers (including
FC).
HARDWARE
Controllers supported by the iir driver include:
o Intel RAID Controller SRCMR
o Intel Server RAID Controller U3-l (SRCU31a)
o Intel Server RAID Controller U3-1L (SRCU31La)
o Intel Server RAID Controller U3-2 (SRCU32)
o All past and future releases of Intel and ICP RAID Controllers.
o Intel RAID Controller SRCU21 (discontinued)
o Intel RAID Controller SRCU31 (older revision, not compatible)
o Intel RAID Controller SRCU31L (older revision, not compatible)
The SRCU31 and SRCU31L can be updated via a firmware update available from Intel.
SEE ALSO cam(4), pass(4), xpt(4), camcontrol(8)AUTHORS
The iir driver is supported and maintained by Achim Leubner <Achim_Leubner@adaptec.com>.
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org> and is based on information supplied by the driver authors and the website
of Mike Smith <msmith@FreeBSD.org>.
BSD August 8, 2004 BSD