Hi, Iam new to unix. I have one input file .
Input file :
ID1~Name1~Place1
ID2~Name2~Place2
ID3~Name3~Place3
I need output such that only first column should change to fixed width column of 15 characters of length.
Output File:
ID1<<12 spaces>>Name1~Place1
ID2<<12... (5 Replies)
- I am looking for different kind of awk solution which I don't think is mentioned before in these forums.
Number of rows in the file are fixed
Their are two columns in file1.txt
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
I am looking for 3... (1 Reply)
Match column 3 in file1 to column 1 in file 2 and replace with column 2 from file2
file 1 sample
SNDK 80004C101 AT
XLNX 983919101 BB
NETL 64118B100 BS
AMD 007903107 CC
KLAC 482480100 DC
TER 880770102 KATS
ATHR 04743P108 KATS... (7 Replies)
Hi all,
I would like to compare a column in one file to a column in another file and when there is a match it prints the first column and the corresponding second column. Example
File1
ABA
ABC
ABE
ABF
File 2
ABA 123
ABB 124
ABD 125
ABC 126
So what I would like printed to a... (6 Replies)
Hello, I am trying to compare 2 files and get only the new lines as output. Note that new lines can be anywhere in the file and not necessarily at the bottom of the file.
I have made the following progress so far.
/home/aa>cat old.txt
0001 732 A
0002 732 C
0005 732 D... (7 Replies)
Hi,
I have two input files as
File1 :
ABC:client1:project1
XYZ:client2-aa:project2
DEF:client4:proj
File2 :
client1:W-170:xx
client2-aa:WT-04:yy
client4:L-005A:zz
Also, array of valid values can be hardcoded like
Output :
ABC:W:project1
XYZ:WT:project2 (1 Reply)
Hi,
I wanted to check whether the x,y,z coordinates of two files are equal or not. At times, when one file is converted to another suitable file extension , there are some chances that the data mismatch would happen during the conversion. In order to avoid the data misfit, i would like to... (6 Replies)
Hi,
I have a file1 whose 17th column needs to be checked if it exists in between the values of column 2 & column 3 as mentioned in another file2. Output of the matched value to be put in separate file 3 & 4.
File1:
... (10 Replies)
Discussion started by: siramitsharma
10 Replies
LEARN ABOUT DEBIAN
debconf-set-selections
DEBCONF-SET-SELECTIONS(1) Debconf DEBCONF-SET-SELECTIONS(1)NAME
debconf-set-selections - insert new default values into the debconf database
SYNOPSIS
debconf-set-selections file
debconf-get-selections | ssh newhost debconf-set-selections
DESCRIPTION
debconf-set-selections can be used to pre-seed the debconf database with answers, or to change answers in the database. Each question will
be marked as seen to prevent debconf from asking the question interactively.
Reads from a file if a filename is given, otherwise from stdin.
WARNING
Only use this command to seed debconf values for packages that will be or are installed. Otherwise you can end up with values in the
database for uninstalled packages that will not go away, or with worse problems involving shared values. It is recommended that this only
be used to seed the database if the originating machine has an identical install.
DATA FORMAT
The data is a series of lines. Lines beginning with a # character are comments. Blank lines are ignored. All other lines set the value of
one question, and should contain four values, each separated by one character of whitespace. The first value is the name of the package
that owns the question. The second is the name of the question, the third value is the type of this question, and the fourth value (through
the end of the line) is the value to use for the answer of the question.
Alternatively, the third value can be "seen"; then the preseed line only controls whether the question is marked as seen in debconf's
database. Note that preseeding a question's value defaults to marking that question as seen, so to override the default value without
marking a question seen, you need two lines.
Lines can be continued to the next line by ending them with a "" character.
EXAMPLES
# Force debconf priority to critical.
debconf debconf/priority select critical
# Override default frontend to readline, but allow user to select.
debconf debconf/frontend select readline
debconf debconf/frontend seen false
OPTIONS --verbose, -v
verbose output
--checkonly, -c
only check the input file format, do not save changes to database
SEE ALSO debconf-get-selections(1) (available in the debconf-utils package)
AUTHOR
Petter Reinholdtsen <pere@hungry.com>
2012-09-10 DEBCONF-SET-SELECTIONS(1)