|
|
Sponsored Content
Operating Systems
Linux
Please correct me with my code?
Post 302477788 by Corona688 on Monday 6th of December 2010 11:00:35 AM
12-06-2010
|
|
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
#!/bin/ksh
LOG_DATE=`date +%Y%m`
export LOG_DATE
cd D:/Informatica/Informatica_share/SrcFiles/l
# mv SITE_ACTIVITY${LOG_DATE}*.CSV D:/Informatica/Informatica_share/SrcFiles/SITE_ACTIVITY${LOG_DATE}*.CSV
# mv SITE_ACTIVITY20050914114546.CSV... (6 Replies)
Discussion started by: vivekanandarpat
6 Replies
2. UNIX for Advanced & Expert Users
#!/bin/ksh
LOG_DATE=`date +%Y%m`
export LOG_DATE
cd D:/Informatica/Informatica_share/SrcFiles/l
# mv SITE_ACTIVITY${LOG_DATE}*.CSV D:/Informatica/Informatica_share/SrcFiles/SITE_ACTIVITY${LOG_DATE}*.CSV
# mv SITE_ACTIVITY20050914114546.CSV... (2 Replies)
Discussion started by: vivekanandarpat
2 Replies
3. Shell Programming and Scripting
Hi,
Some part of output:
================
$ hwmgr show scsi
SCSI DEVICE DEVICE DRIVER NUM DEVICE FIRST
HWID: DEVICEID HOSTNAME TYPE SUBTYPE OWNER PATH FILE VALID PATH
-------------------------------------------------------------------------
68: ... (10 Replies)
Discussion started by: mansa
10 Replies
4. Shell Programming and Scripting
I have input file like this
Input file:
ABC|abc_etc_passwd
XYZ|XYZ_etc_passwd
zXY|XYZ_etc_passwd
IJK|test_etc_passwd
KLM|test_etc_passwd
i want to do following in a loop.
grep 'ABC' *abc_etc_passwd*
grep 'XYZ' *XYZ_etc_passwd*
grep 'ZXY' *ZXY_etc_passwd*
i have tried this
for i... (2 Replies)
Discussion started by: pinnacle
2 Replies
5. Solaris
I am new to solaris and I replaced a faulty tape drive sun DLT7000
But, I am getting the follwoing error when system reboots
ltid deamon error drive index 1 is not correct, drive name /dev/rmt/2cbn is incorrect no such file or directory.
I have two drives the other one is /dev/rmt/0cbn,... (8 Replies)
Discussion started by: latif1958
8 Replies
6. Shell Programming and Scripting
###############
#filename.sh
###############
CUREENT_DATE=02
log_file_path="$CUREENT_DATE"-"${0##%*/}`|cut -d "." -f1|awk -F "/" '{print $NF}'`"".log"
echo $log_file_path
################
#output required
02-filename.log (6 Replies)
Discussion started by: mohitmehral
6 Replies
7. Shell Programming and Scripting
Hello all; hope someone can help me cause I am going crazy trying to find a solution for (what I think is simple) issue...looked hard up and down this forum and tried several "solutions" with no avail...so here's my issue:
I have this (parent) script: copylsofdcmcadefttosftpwithmove.sh
... (3 Replies)
Discussion started by: gvolpini
3 Replies
8. Shell Programming and Scripting
Hello Brains,
I was trying to develop a script that would do nslookup using both name and ip of server and format the output and store in an output file. Please find the script below.
#!/usr/bin/ksh
cat $1 | tr "" "" |
while read ip name
do
ERROR="$(nslookup $ip | grep can't | awk -F"... (2 Replies)
Discussion started by: Praveen P
2 Replies
9. Shell Programming and Scripting
Hi everyone,
The following piece of awk code works fine if I use eval builtin
var='$1,$2'
ps | eval "awk '{print $var}'"
But when I try to knock off eval and use awk variable as substitute then I am not getting the expected result
ps | awk -v v1=$var '{print v1}' # output is $1,$2
ps |... (4 Replies)
Discussion started by: royalibrahim
4 Replies
10. Shell Programming and Scripting
Dear all,
I am using sed as an alternative to grep in order to get a specific line from each of multiple files located in the same directory. I am using sed because it prints the lines in the correct order (unlike grep).
When I write sed code that prints out the output I get it correct, but... (1 Reply)
Discussion started by: JaNaJaNa
1 Replies
LEARN ABOUT REDHAT
qmail-control
qmail-control(5) File Formats Manual qmail-control(5) NAME
qmail-control - qmail configuration files INTRODUCTION
You can change the behavior of the qmail system by modifying qmail's control files in /var/lib/qmail/control. qmail can survive with just one control file, me, containing the fully-qualified name of the current host. This file is used as the default for other hostname-related control files. Comments are allowed in badmailfrom, locals, percenthack, qmqpservers, rcpthosts, smtproutes, and virtualdomains. Trailing spaces and tabs are allowed in any control file. The following table lists all control files other than me. See the corresponding man pages for further details. control default used by badmailfrom (none) qmail-smtpd bouncefrom MAILER-DAEMON qmail-send bouncehost me qmail-send concurrencylocal 10 qmail-send concurrencyremote 20 qmail-send defaultdomain me qmail-inject defaulthost me qmail-inject databytes 0 qmail-smtpd doublebouncehost me qmail-send doublebounceto postmaster qmail-send envnoathost me qmail-send helohost me qmail-remote idhost me qmail-inject localiphost me qmail-smtpd locals me qmail-send morercpthosts (none) qmail-smtpd percenthack (none) qmail-send plusdomain me qmail-inject qmqpservers (none) qmail-qmqpc queuelifetime 604800 qmail-send rcpthosts (none) qmail-smtpd smtpgreeting me qmail-smtpd smtproutes (none) qmail-remote timeoutconnect 60 qmail-remote timeoutremote 1200 qmail-remote timeoutsmtpd 1200 qmail-smtpd virtualdomains (none) qmail-send SEE ALSO
qmail-inject(8), qmail-qmqpc(8), qmail-remote(8), qmail-send(8), qmail-showctl(8), qmail-smtpd(8) qmail-control(5)