Sponsored Content
Full Discussion: Laptop device interface
Top Forums UNIX for Dummies Questions & Answers Laptop device interface Post 302476363 by Corona688 on Wednesday 1st of December 2010 02:10:03 PM
Old 12-01-2010
Quote:
Originally Posted by neur0n
oh, so it just like a desktop except they don't have the slots?
Yes, everything's hardwired right in, nearly. The PCI interface is kept so the operating system can tell what drivers to use for everything through plug-and-play.

Laptops usually do have one mini-PCI/PCI-e slot though, because getting a product approved for wireless is a pain. They'd much rather buy an approved wireless card off-the-shelf than put their entire laptop through some slow, expensive FCC test procedure every time they switch wireless chipset manufacturers.
 

9 More Discussions You Might Find Interesting

1. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

2. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

3. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

4. Ubuntu

Connect 2 laptops with RJ45 cable (Ubuntu 10.10 laptop with Windows 7 laptop)

Hi to all, I have the problem that a laptops with windows XP cannot startup even in safe mode nor using last good known configuration. I have a Ubuntu 10.10 Live CD and booting from it I can read the Hard Drive. I need to do a backup the Hard Drive from XP laptop and I want to connect this... (5 Replies)
Discussion started by: cgkmal
5 Replies

5. Red Hat

Find out which eth or device belongs to interface "port 1 PCI 4"

Hi, I´ve given only this info to configure a network interface : "port 1 PCI 4" I´ve been searching for any kind of relationship in the system which allow me to find the etc that must be configured... Please, could anybody help me? rhxx:#/root# lspci |grep -i "PCI BRIDGE" 00:01.0 PCI... (0 Replies)
Discussion started by: pabloli150
0 Replies

6. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

7. Red Hat

Wlan0: unknown interface: No such device

Hi All, Am using Toshiba Satellite C850-l5212 Laptop . I have installed RHEL6 server on it ( Linux 2.6.32-220.el6.x86_64 ) I Installed wireless driver ( linux_mac80211_0012.0207.2013.tar.bz2 ) and the installation went fine. But when i do ifconfig wlan0 up its giving the below error .... (0 Replies)
Discussion started by: senthilcaesar
0 Replies

8. Ubuntu

Laptop to laptop transfer files

Dear all, I would like to transfer my old laptop documents/files etc to the new laptop without using any external hard disk. Please let me know if its possible via any way. Thank in advance, emily (3 Replies)
Discussion started by: emily
3 Replies

9. Hardware

Problem with Broadcom BCM43225 wifi interface on an Acer Aspire laptop

Hi This is a question about Broadcom BCM43225 wifi interface on an Acer Aspire laptop I just had a fresh install of ubuntu 16.04 on my acer aspire laptop and I am having a difficult issue with my wifi connection. Every time I restart my laptop I get the wifi connection working, but after a... (0 Replies)
Discussion started by: faizlo
0 Replies
DEVICE(9)						   BSD Kernel Developer's Manual						 DEVICE(9)

NAME
device -- an abstract representation of a device SYNOPSIS
typedef struct device *device_t; DESCRIPTION
The device object represents a piece of hardware attached to the system such as an expansion card, the bus which that card is plugged into, disk drives attached to the expansion card etc. The system defines one device, root_bus and all other devices are created dynamically during autoconfiguration. Normally devices representing top-level busses in the system (ISA, PCI etc.) will be attached directly to root_bus and other devices will be added as children of their relevant bus. The devices in a system form a tree. All devices except root_bus have a parent (see device_get_parent(9)). In addition, any device can have children attached to it (see device_add_child(9), device_add_child_ordered(9), device_find_child(9), device_get_children(9), and device_delete_child(9)). A device which has been successfully probed and attached to the system will also have a driver (see device_get_driver(9) and driver(9)) and a devclass (see device_get_devclass(9) and devclass(9)). Various other attributes of the device include a unit number (see device_get_unit(9)), verbose description (normally supplied by the driver, see device_set_desc(9) and device_get_desc(9)), a set of bus-spe- cific variables (see device_get_ivars(9)) and a set of driver-specific variables (see device_get_softc(9)). Devices can be in one of several states: DS_NOTPRESENT the device has not been probed for existence or the probe failed DS_ALIVE the device probe succeeded but not yet attached DS_ATTACHED the device has been successfully attached DS_BUSY the device is currently open The current state of the device can be determined by calling device_get_state(9). SEE ALSO
devclass(9), driver(9) AUTHORS
This manual page was written by Doug Rabson. BSD
June 16, 1998 BSD
All times are GMT -4. The time now is 11:22 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy