thanks but the question is still there . how can i remove these ce3 and ce4 from dladm output. ifconfig -a does not show ce3 and ce4 as they are not being used.
Code:
Last edited by DukeNuke2; 11-26-2010 at 11:10 AM..
Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this:
dladm create aggr -d ce0 -d ce1 key
Do I need to... (1 Reply)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Can anyone please explain what does these means ?
# dladm show-dev
nxge0 link: up speed: 1000 Mbps duplex: full
nxge1 link: up speed: 1000 Mbps duplex: full
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 ... (6 Replies)
hello everyone, I'm a new user and unix-beginner.
I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc
and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Hi all,
I want to remove the remove bracket sign ( ) and put in the separate column I also want to remove the repeated entry like in first row in below input (PA156) is repeated
ESR1 (PA156) leflunomide (PA450192) (PA156) leflunomide (PA450192)
CHST3 (PA26503) docetaxel... (2 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi all,
I have never wondered where is the mapping of the link names to physical device path display under
dladm show-phys until today.
fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
Discussion started by: javanoob
1 Replies
LEARN ABOUT OPENSOLARIS
ixgbe
ixgbe(7D) Devices ixgbe(7D)NAME
ixgbe - Intel 10Gb PCI Express NIC Driver
SYNOPSIS
/dev/ixgbe*
DESCRIPTION
The ixgbe Gigabit Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider
Interface, dlpi(7P), on Intel 82598 10-Gigabit Ethernet controllers.
The ixgbe driver functions include controller initialization, frame transmit and receive, promiscuous and multicast support, and error
recovery and reporting.
The ixgbe driver and hardware support auto-negotiation, a protocol specified by the IEEE 802.3ae specification.
APPLICATION PROGRAMMING INTERFACE
The cloning character-special device, /dev/ixgbe, is used to access all Intel 82598 10 -Gigabit Ethernet devices installed within the
system.
The ixgbe driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of ixgbe instances and for
ixgbe instances to be aggregated. See dladm(1M) for more details.
You must send an explicit DL_ATTACH_REQ message to associate the opened stream with a particular device (PPA). The PPA ID is interpreted as
an unsigned integer data type and indicates the corresponding device instance (unit) number. The driver returns an error (DL_ERROR_ACK) if
the PPA field value does not correspond to a valid device instance number for the system. The device is initialized on first attach and de-
initialized (stopped) at last detach.
The values returned by the driver in the DL_INFO_ACK primitive in response to your DL_INFO_REQ are:
o Maximum SDU is 16366.
o Minimum SDU is 0.
o DLSAP address length is 8.
o MAC type is DL_ETHER.
o SAP (Service Access Point) length value is -2, meaning the physical address component is followed immediately by a 2-byte SAP
component within the DLSAP address.
o Broadcast address value is the Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF).
Once in the DL_ATTACHED state, you must send a DL_BIND_REQ to associate a particular SAP with the stream.
CONFIGURATION
By default, the ixgbe driver performs auto-negotiation to select the link speed and mode. Link speed and mode can only be 10000 Mbps full-
duplex. See the IEEE802.3 standard for more information.
FILES
/dev/ixgbe* Special character device.
/kernel/drv/ixgbe 32-bit device driver (x86).
/kernel/drv/amd64/ixgbe 64-bit device driver (x86).
/kernel/drv/sparcv9/ixgbe 64-bit device driver (SPARC).
/kernel/drv/ixgbe.conf Configuration file.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------------------------------------+
|ATTRIBUTE TYPE ATTRIBUTE VALUE |
|Availability SUNWixgbe |
|Architecture SPARC, x86 |
|Interface Stability Committed |
+-----------------------------------------------------------+
SEE ALSO dladm(1M), netstat(1M), driver.conf(4), attributes(5), streamio(7I), dlpi(7P)
Writing Device Drivers
STREAMS Programming Guide
Network Interfaces Programmer's Guide
IEEE 802.3ae Specificiation, IEEE - 2002
SunOS 5.11 20 Mar 2008 ixgbe(7D)