thanks but the question is still there . how can i remove these ce3 and ce4 from dladm output. ifconfig -a does not show ce3 and ce4 as they are not being used.
Code:
Last edited by DukeNuke2; 11-26-2010 at 11:10 AM..
Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this:
dladm create aggr -d ce0 -d ce1 key
Do I need to... (1 Reply)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Can anyone please explain what does these means ?
# dladm show-dev
nxge0 link: up speed: 1000 Mbps duplex: full
nxge1 link: up speed: 1000 Mbps duplex: full
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 ... (6 Replies)
hello everyone, I'm a new user and unix-beginner.
I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc
and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Hi all,
I want to remove the remove bracket sign ( ) and put in the separate column I also want to remove the repeated entry like in first row in below input (PA156) is repeated
ESR1 (PA156) leflunomide (PA450192) (PA156) leflunomide (PA450192)
CHST3 (PA26503) docetaxel... (2 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi all,
I have never wondered where is the mapping of the link names to physical device path display under
dladm show-phys until today.
fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
Discussion started by: javanoob
1 Replies
LEARN ABOUT FREEBSD
ntb
NTB(4) BSD Kernel Interfaces Manual NTB(4)NAME
ntb, ntb_hw, if_ntb -- Intel(R) Non-Transparent Bridge driver
SYNOPSIS
To compile this driver into your kernel, place the following lines in your kernel configuration file:
device ntb_hw
device if_ntb
Or, to load the driver as a module at boot, place the following line in loader.conf(5):
if_ntb_load="YES"
DESCRIPTION
The ntb driver provides support for the Non-Transparent Bridge (NTB) in the Intel S1200, Xeon E3 and Xeon E5 processor families.
The NTB allows you to connect two computer systems using a PCI-e link if they have the correct equipment and connectors.
CONFIGURATION
The NTB memory windows need to be configured by the BIOS. If your BIOS allows you to set their size, you should set the size of both memory
windows to 1 MiB. This needs to be done on both systems.
Each system needs to have a different IP address assigned. The MAC address is randomly generated. Also for maximum performance, the MTU
should be set to 16 kiB. This can be done by adding the line below to rc.conf(5):
ifconfig_ntb0="inet 192.168.1.10 netmask 255.255.255.0 mtu 16384"
And on the second system :
ifconfig_ntb0="inet 192.168.1.11 netmask 255.255.255.0 mtu 16384"
If you are using the UDP protocol, you may want to increase the net.inet.udp.maxdgram sysctl(8) variable.
SEE ALSO rc.conf(5), sysctl(8)AUTHORS
The ntb driver was developed by Intel and originally written by Carl Delsey <carl@FreeBSD.org>.
BUGS
If the driver is unloaded, it cannot be reloaded without a system reboot.
The network support is limited. It isn't fully configurable yet. It also isn't integrated into netgraph(4) or bpf(4).
NTB to Root Port mode is not yet supported.
There is no way to protect your system from malicious behavior on the other system once the link is brought up. Anyone with root or kernel
access on the other system can read or write to any location on your system. In other words, only connect two systems that completely trust
each other.
BSD Apr 11, 2013 BSD