The supplied command sar it probably what you are after. If you are after the value since last boot, just fire it off without parameters. Depending on your installation, you may get hourly or 5 minute stats, but it is averaged at the end. This is usually controlled by the running of sa1, often by the cron table of user account adm.
The columns are usually %usr %sys %wio %idle, so it's up to you to decide if you want 100-%idle or if I/O wait should be considered.
If this answers what you need, great.
If you need average at the moment, you can supply a variety of parameters. You could have
... which gets the information from the last 1 second. You can stretch this by increasing the first value. You can vary it by increaing the second value to show you more samples, e.g.
... will report the usage over the last 3 seconds 5 times and then an average.
There are also reports generated by sa2, again usually by the cron table of adm. Read your manaul pages about sa2 for where this file is likely to be in your implementation if you have it enabled.
hi,
AIX 5.3
For any command(say tar command) I am getting 100% busy for my hdisk.
But my CPU and Memory is not busy and have more idle also.
Please advice for any performance analysing.
Thanks in Advance, (3 Replies)
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
Hi,
How can I find total CPU usage in percentage? e.g. if my system has 8 CPUs and I want to list total usage for all of them, is it possible through a command?
I have tried some of the commands like top, mpstat, sar. The output of those commands has to be manipulated to derive the percentage... (14 Replies)
Hi all,
Is it possible to get total memory usage and free memory usage without top? By Googling I found for total memory usage, use vmstat, for CPU, use mpstat, for disk I/O use iostat, is this correct? Will using sar gives the same result as ALL of these three (3) commands?
What about if I... (2 Replies)
Hi all
Can anyone advise/confirm whether total CPU usage when running sar is %user+%system+%iowait or is it %user+%system only?
I want to confirm whether I am having a CPU-bound problem or not.
This is a single-CPU VMware machine.
$ sar 5 20
Linux 2.6.18-238.5.1.el5... (7 Replies)
Hi,
I want to calculate the total cpu usage from the sar report. Say for example,
Linux 2.6.24-21-generic (blade10) 09/10/2012
04:54:36 PM CPU %user %nice %system %iowait %steal %idle
04:54:37 PM all 0.00 0.00 0.00 0.00 ... (1 Reply)
hi, i am using solaris server. I want to find the total CPU usage on a server. Top command will give that result, but here that command is not working. So anyone can help me to find the total CPU usage. (2 Replies)
Let's say i have 20 users logged on Server. How can I know how much memory percent used each of them is using with system time in each user? (2 Replies)
Trying to use awk to print the lines in file that have either REF or SNV in $3, add a header line, sort by $4 in numerical order. The below code does that already, but where I am stuck is on the last part where the total lines are counted and printed under Total_Targets, under Targets_less_than is... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT ULTRIX
accton
sa(8) System Manager's Manual sa(8)Name
sa, accton - print process accounting statistics
Syntax
/etc/sa [ options ] [ file ]
/etc/accton [ file ]
Arguments
file With an argument naming an existing file, causes system accounting information for every process executed to be placed at the end
of the file. If no argument is given, accounting is turned off.
Description
The command reports on, cleans up, and generally maintains accounting files.
The is able to condense the information in into a summary file which contains a count of the number of times each command was called and
the time resources consumed. This condensation is desirable because on a large system can grow by 100 blocks per day. The summary file is
normally read before the accounting file, so the reports include all available information.
If a file name is given as the last argument, that file will be treated as the accounting file. The file is the default.
Output fields are labeled: "cpu" for the sum of user+system time (in cpu seconds), "re" for real time (also in cpu seconds), "k" for cpu-
time averaged core usage (in 1k units), "avio" for average number of I/O operations per execution. With options fields labeled "tio" for
total I/O operations, "k*sec" for cpu storage integral (kilo-core seconds), "u" and "s" for user and system cpu time alone (both in cpu
seconds) will sometimes appear.
Options-a List all command names including those containing unprintable characters and those used only once. By default, places all command
names containing unprintable characters and those used only once under the name `***other.'
-b Sort output by sum of user and system time divided by number of calls. Default sort is by sum of user and system times.
-c Besides total user, system, and real time for each command, print percentage of total time over all commands.
-d Sort by average number of disk I/O operations.
-D Print and sort by total number of disk I/O operations.
-f Force no interactive threshold compression with option.
-i Do not read in summary file.
-j Instead of total minutes for each category, give seconds per call.
-k Sort by cpu-time average memory usage.
-K Print and sort by cpu-storage integral.
-l Separate system and user time; normally they are combined.
-m Print number of processes and number of CPU minutes for each user.
-n Sort by number of calls.
-r Reverse order of sort.
-s Merge accounting file into summary file when done.
-t For each command, report ratio of real time to the sum of user and system times. If the sum of user and system times is too small
to report, `*ignore*' appears in this field.
-u Superseding all other flags, print for each command in the accounting file the user ID and command name.
-v Followed by a number n, types the name of each command used n times or fewer. Await a reply from the terminal; if it begins with
`y', add the command to the category `**junk**.' This is used to strip out garbage.
Restrictions
Accounting is suspended when there is less than 2% free space on disk. Accounting resumes when free space rises above 4%.
Files
Raw accounting
Summary
Per-user summary
See Alsoacct(2), ac(8)sa(8)