Sponsored Content
Full Discussion: remove interface from dladm
Operating Systems Solaris remove interface from dladm Post 302474912 by DukeNuke2 on Friday 26th of November 2010 02:00:19 AM
Old 11-26-2010
you can't remove them from dladm... this command shows all available interfaces in the system. use "ifconfig -a" output.
and if "show-aggr" doensn't show an output, there is no aggregation set confugured.
This User Gave Thanks to DukeNuke2 For This Post:
 

9 More Discussions You Might Find Interesting

1. Solaris

dladm use

Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this: dladm create aggr -d ce0 -d ce1 key Do I need to... (1 Reply)
Discussion started by: hshapiro
1 Replies

2. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

3. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

4. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

5. Solaris

ifconfig -a vs dladm show-dev and IP ?

Can anyone please explain what does these means ? # dladm show-dev nxge0 link: up speed: 1000 Mbps duplex: full nxge1 link: up speed: 1000 Mbps duplex: full e1000g0 link: up speed: 1000 Mbps duplex: full e1000g1 ... (6 Replies)
Discussion started by: dehetoxic
6 Replies

6. Solaris

[beginner] dladm create-bridge

hello everyone, I'm a new user and unix-beginner. I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Discussion started by: kimj
12 Replies

7. Shell Programming and Scripting

remove brackets and put it in a column and remove repeated entry

Hi all, I want to remove the remove bracket sign ( ) and put in the separate column I also want to remove the repeated entry like in first row in below input (PA156) is repeated ESR1 (PA156) leflunomide (PA450192) (PA156) leflunomide (PA450192) CHST3 (PA26503) docetaxel... (2 Replies)
Discussion started by: manigrover
2 Replies

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

9. Solaris

Solaris 11.4.2.3.0 - dladm link names mapping

Hi all, I have never wondered where is the mapping of the link names to physical device path display under dladm show-phys until today. fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
Discussion started by: javanoob
1 Replies
dlmgmtd(1M)						  System Administration Commands					       dlmgmtd(1M)

NAME
dlmgmtd - datalink management daemon SYNOPSIS
/sbin/dlmgmtd svc:/network/datalink-management:default DESCRIPTION
dlmgmtd is a system daemon that handles administrative events for network datalink interfaces. It is controlled through the service manage- ment facility (SMF) service instance: svc:/network/datalink-management:default The daemon should not be invoked directly. It does not constitute an administrative nor a programming interface. The administrative inter- face for managing datalinks is dladm(1M). OPTIONS
The daemon has no options. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsr | +-----------------------------+-----------------------------+ |Interface Stability |Private | +-----------------------------+-----------------------------+ SEE ALSO
dladm(1M), attributes(5) SunOS 5.11 30 Jul 2008 dlmgmtd(1M)
All times are GMT -4. The time now is 05:49 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy