remove interface from dladm Post: 302474912

9 More Discussions You Might Find Interesting

1. Solaris

dladm use

Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this: dladm create aggr -d ce0 -d ce1 key Do I need to...

2. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

3. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

4. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

5. Solaris

ifconfig -a vs dladm show-dev and IP ?

Can anyone please explain what does these means ? # dladm show-dev nxge0 link: up speed: 1000 Mbps duplex: full nxge1 link: up speed: 1000 Mbps duplex: full e1000g0 link: up speed: 1000 Mbps duplex: full e1000g1 ...

6. Solaris

[beginner] dladm create-bridge

hello everyone, I'm a new user and unix-beginner. I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it...

7. Shell Programming and Scripting

remove brackets and put it in a column and remove repeated entry

Hi all, I want to remove the remove bracket sign ( ) and put in the separate column I also want to remove the repeated entry like in first row in below input (PA156) is repeated ESR1 (PA156) leflunomide (PA450192) (PA156) leflunomide (PA450192) CHST3 (PA26503) docetaxel...

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

9. Solaris

Solaris 11.4.2.3.0 - dladm link names mapping

Hi all, I have never wondered where is the mapping of the link names to physical device path display under dladm show-phys until today. fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is...

LEARN ABOUT MINIX

inet_type

inet_type(4)							   File Formats 						      inet_type(4)

NAME

       inet_type - default Internet protocol type

SYNOPSIS

       /etc/default/inet_type

DESCRIPTION

       The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.

       The  inet_type  file  can  contain  a  number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
       assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.

       The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file.  By  default,
       both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
       setting the value of DEFAULT_IP.  The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
       will be displayed:

       IP_VERSION4     Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
		       and netstat(1M) commands.

       IP_VERSION6     Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       BOTH	       Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For  example,
       even if the value of DEFAULT_IP is IP_VERSION4, the command

       example% ifconfig -a6

       will display all IPv6 interfaces.

EXAMPLES

       Example 1: Suppressing IPv6 Related Output

       This is what the inet_type file must contain if you want to suppress IPv6 related output:

       DEFAULT_IP=IP_VERSION4

SEE ALSO

       ifconfig(1M), netstat(1M)

SunOS 5.10							    16 Jun 1999 						      inet_type(4)