11-23-2010
You don't need nimsh.
Are you using concurrent vg's?
This User Gave Thanks to firefox111 For This Post:
10 More Discussions You Might Find Interesting
1. AIX
(0 Replies)
Discussion started by: mhenryj
0 Replies
2. AIX
Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
Discussion started by: mhenryj
1 Replies
3. AIX
Hi Guys,
I have two nodes clustered. Each node is AIX 5.2 & they are clustered with HACMP 5.2. The mode of the cluster is Active/Passive which mean one node is the Active node & have all resource groups on it & the 2nd node is standby.
Last Monday I noted that all resource groupes have been... (2 Replies)
Discussion started by: aldowsary
2 Replies
4. HP-UX
Hi,
Can anybody advice whether it is possible to configure HACMP in HP-UX Server.
To my knowledge HACMP is IBM Solution.
Thanks && Regards,
N. Poorna Chandra Rao. (2 Replies)
Discussion started by: npcrao
2 Replies
5. Shell Programming and Scripting
hi,
how to access console of a switch having rj45 on switch side to db 9 female on pc side console cable which needs to be connected to one console server having rj11 on its side and db 9 female on other end.i.e. on switch side,console cable has rj45 and db 9 pin female connector on other side of... (1 Reply)
Discussion started by: pankajd
1 Replies
6. AIX
Hi,
Can we use network for heartbeat, I mean can we use different network card for heartbeat. (6 Replies)
Discussion started by: vjm
6 Replies
7. AIX
hi
can anyone explain the concepts of HACMP and configuration (step by step) (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
8. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
9. AIX
Hi,
I have question about HA. I have 2 node cluster (node A and node B). I have configured network and disk HB. If my network is up and i remove both the fc cables from node A will my cluster failover to node B? I have checked and its not working, if i want my cluster to failover in this... (5 Replies)
Discussion started by: powerAIX
5 Replies
10. AIX
Dear all
i have two aix system
-Model : P770
-OS version: AIX 6.1
-patch level : 6100-07-04-1216
-ha version : HACMP v 6.1.0.8
-host : A, B
last Wednesday, my B system suddenly went down with crash dump. after 1 minute, A system went down with crash dump. I checked the dump of A-system... (6 Replies)
Discussion started by: tomato00
6 Replies
maxuprc(5) File Formats Manual maxuprc(5)
NAME
maxuprc - limits the maximum number of concurrent user processes per user
VALUES
Failsafe
Default
Allowed values
Recommended value
DESCRIPTION
is a dynamic tunable that limits the maximum number of processes per user. Only root can have more than the number of processes limited by
Who is Expected to Change This Tunable?
System administrators can change the value of depending on the usage of the system.
Restrictions on Changing
None. This tunable is dynamic.
When Should the Value of This Tunable Be Raised?
The value of should be changed if users require more processes than what they are currently allowed by If fails with an error value of it
could be an indication that was reached by that particular user. However, that is not the only reason that could cause to fail with an
errno value of may be returned if system tunable has been reached or memory on the system has been exhausted.
What Are the Side Effects of Raising the Value?
Raising the value of allows a single user to consume a greater percentage of the system resources.
When Should the Value of This Tunable Be Lowered?
The value of should be lowered when individual users are monopolizing system resources by running too many concurrent processes.
What Are the Side Effects of Lowering the Value?
Applications that depend on a large number of processes may behave differently or fail. Existing processes will continue to run but new
process creations which would result in the user exceeding will fail.
What Other Tunable Values Should Be Changed at the Same Time?
When tuning you should keep in mind the value of
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
SEE ALSO
nproc(5).
Tunable Kernel Parameters maxuprc(5)