11-23-2010
HACMP switchover
Hi
If I start the cluster now in node A using "smitty clstart", wont the resource groups come to node A from node B
10 More Discussions You Might Find Interesting
1. AIX
(0 Replies)
Discussion started by: mhenryj
0 Replies
2. AIX
Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
Discussion started by: mhenryj
1 Replies
3. AIX
Hi Guys,
I have two nodes clustered. Each node is AIX 5.2 & they are clustered with HACMP 5.2. The mode of the cluster is Active/Passive which mean one node is the Active node & have all resource groups on it & the 2nd node is standby.
Last Monday I noted that all resource groupes have been... (2 Replies)
Discussion started by: aldowsary
2 Replies
4. HP-UX
Hi,
Can anybody advice whether it is possible to configure HACMP in HP-UX Server.
To my knowledge HACMP is IBM Solution.
Thanks && Regards,
N. Poorna Chandra Rao. (2 Replies)
Discussion started by: npcrao
2 Replies
5. Shell Programming and Scripting
hi,
how to access console of a switch having rj45 on switch side to db 9 female on pc side console cable which needs to be connected to one console server having rj11 on its side and db 9 female on other end.i.e. on switch side,console cable has rj45 and db 9 pin female connector on other side of... (1 Reply)
Discussion started by: pankajd
1 Replies
6. AIX
Hi,
Can we use network for heartbeat, I mean can we use different network card for heartbeat. (6 Replies)
Discussion started by: vjm
6 Replies
7. AIX
hi
can anyone explain the concepts of HACMP and configuration (step by step) (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
8. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
9. AIX
Hi,
I have question about HA. I have 2 node cluster (node A and node B). I have configured network and disk HB. If my network is up and i remove both the fc cables from node A will my cluster failover to node B? I have checked and its not working, if i want my cluster to failover in this... (5 Replies)
Discussion started by: powerAIX
5 Replies
10. AIX
Dear all
i have two aix system
-Model : P770
-OS version: AIX 6.1
-patch level : 6100-07-04-1216
-ha version : HACMP v 6.1.0.8
-host : A, B
last Wednesday, my B system suddenly went down with crash dump. after 1 minute, A system went down with crash dump. I checked the dump of A-system... (6 Replies)
Discussion started by: tomato00
6 Replies
LEARN ABOUT HPUX
cmrunnode
cmrunnode(1m) cmrunnode(1m)
NAME
cmrunnode - run a node in a high availability cluster
SYNOPSIS
cmrunnode [-v] [node_name...] [-t | -w none]
DESCRIPTION
cmrunnode causes a node to start its cluster daemon to join the existing cluster. This command verifies the network configuration before
causing the node to start its cluster daemon.
To start a cluster on one of its nodes, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the clus-
ter configuration file. See access policy in cmquerycl(1m).
Starting a node will not cause any active packages to be moved to the new node. However, if a package is DOWN, has its switching enabled,
and is able to run on the new node, that package will automatically run there.
If node_name is not specified, the cluster daemon will be started on the local node and will join the existing cluster.
Options
cmrunnode supports the following options:
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages. The -w
option is not required with the -t option as -t does not validate network connectivity, but assumes that all the nodes can meet
any external dependencies such as EMS resources, package subnets, and storage.
node_name...
Start the cluster daemon on the specified node(s).
-w none
By default network probing is performed to check that the network connectivity is the same as when the cluster was configured.
Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The option should
only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmrunnode returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon on the current node:
cmrunnode
Run the cluster daemons on node1 and node2:
cmrunnode node1 node2
AUTHOR
cmrunnode was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmruncl(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmrunnode(1m)