11-17-2010
Yes but those are general guidelines, your vendor may have some specific recommendations.
9 More Discussions You Might Find Interesting
1. Solaris
Thinking of using our San for network backups..
Have a Netra 240 being installed and planning to get some space on our San.
Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Discussion started by: frustrated1
1 Replies
2. Filesystems, Disks and Memory
Hi,
I have an existing SUN server that has a SAN storage installed on it. It also has softwares like Appwrox(scheduler), Taradata (database client), Samba Share and a few more installed on it.
Now suppose that I have a new unix server server and i switch the same SAN store from the old unix... (1 Reply)
Discussion started by: myloginid
1 Replies
3. AIX
I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Discussion started by: daveisme
1 Replies
4. Solaris
Hi,
I have configured our SAN Storage to be connected to our new SUN T5220.
On the SAn it looks all fine
on the server I do not see any connection:
cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected ... (4 Replies)
Discussion started by: manni2
4 Replies
5. Red Hat
Hello,
I am using LINUX OS. I want to check what is the SAN storage size. How do i check this in server? Any help is really appreciated.. (3 Replies)
Discussion started by: govindts
3 Replies
6. Solaris
HI all,
I had recently change the Server storage from EMC to the IBM SAN.
but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server.
When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies
7. Solaris
Hi,
We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN.
The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes).
I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
Discussion started by: esmgr
4 Replies
8. AIX
Can anyone recommend a good book on san storage basics and how it communicates with an AIX server? (1 Reply)
Discussion started by: NycUnxer
1 Replies
9. Solaris
hi all,
I am on solaris 10 1/13 and new to SAN storage.
I am required to connect to the LUNs on the SAN storage and is asked to provide the WWN information to the storage administrator.
Right now, it will be just 1 connection from a single hba port to the FCport on the storage directly,... (1 Reply)
Discussion started by: javanoob
1 Replies
LEARN ABOUT CENTOS
scsi-rescan
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1)
NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting
SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]]
OPTIONS
-a, --alltargets
scan all targets, not just currently existing [default: disabled]
-d enable debug [default: 0]
-l activates scanning for LUNs 0--7 [default: 0]
-L NUM activates scanning for LUNs 0--NUM [default: 0]
-w, --wide
scan for target device IDs 0--15 [default: 0--7]
-c enables scanning of channels 0 1 [default: 0 / all detected ones]
-r, --remove
enables removing of devices [default: disabled]
-f, --flush
flush failed multipath devices [default: disabled]
-i, --issue-lip
issue a FibreChannel LIP reset [default: disabled]
-u, --update
look for existing disks that have been remapped
-s, --resize
look for resized disks and reload associated multipath devices, if applicable
--forcerescan
rescan existing devices
--forceremove
remove and readd every device (DANGEROUS)
--nooptscan
don't stop looking for LUNs is 0 is not found
--color
use coloured prefixes OLD/NEW/DEL
--hosts=LIST
scan only host(s) in LIST
--channels=LIST
scan only channel(s) in LIST
--ids=LIST
scan only target ID(s) in LIST
--luns=LIST
scan only lun(s) in LIST
--sync, --nosync
issue a sync / no sync [default: sync if remove]
--attachpq3
tell kernel to attach sg to LUN 0 that reports PQ=3
--reportlun2
tell kernel to try REPORT_LUN even on SCSI2 devices
--largelun
tell kernel to support LUNs > 7 even on SCSI2 devs
--sparselun
tell kernel to support sparse LUN numbering
Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended).
LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.)
SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi
sg3_utils Homepage: http://sg.danny.cz/sg
rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)