Sponsored Content
Full Discussion: Storage from SAN
Top Forums UNIX for Dummies Questions & Answers Storage from SAN Post 302472336 by kopper on Wednesday 17th of November 2010 12:49:32 PM
Old 11-17-2010
well that's the thing I read in other post that those are since the multipath is not started during bootup

but I just got home and I found these

kernel: printk: 20 messages suppressed.
kernel: Buffer I/O error on device sdc, logical block 0
kernel: Buffer I/O error on device sdc, logical block 0
kernel: Buffer I/O error on device sdc, logical block 14417919
kernel: Buffer I/O error on device sdc, logical block 0
kernel: Buffer I/O error on device sdd, logical block 0
kernel: Buffer I/O error on device sdd, logical block 0
kernel: Buffer I/O error on device sdd, logical block 14417919
kernel: Buffer I/O error on device sdd, logical block 0
kernel: Buffer I/O error on device sdf, logical block 0

and I left this system 4 hours ago and still getting these messages well those above are the only ones

I get the point during boot up even when the boot up process is slow because of those messages I don't know why while the server is up and running

---------- Post updated at 01:49 PM ---------- Previous update was at 12:37 AM ----------

is there a way to avoid multipath be sensing the passive paths?
 

9 More Discussions You Might Find Interesting

1. Solaris

Using San storage - advice needed

Thinking of using our San for network backups.. Have a Netra 240 being installed and planning to get some space on our San. Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Discussion started by: frustrated1
1 Replies

2. Filesystems, Disks and Memory

Switching SAN storage

Hi, I have an existing SUN server that has a SAN storage installed on it. It also has softwares like Appwrox(scheduler), Taradata (database client), Samba Share and a few more installed on it. Now suppose that I have a new unix server server and i switch the same SAN store from the old unix... (1 Reply)
Discussion started by: myloginid
1 Replies

3. AIX

SAN storage and speed

I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Discussion started by: daveisme
1 Replies

4. Solaris

SAN Storage to solaris 10 server

Hi, I have configured our SAN Storage to be connected to our new SUN T5220. On the SAn it looks all fine on the server I do not see any connection: cfgadm -al Ap_Id Type Receptacle Occupant Condition c1 scsi-bus connected ... (4 Replies)
Discussion started by: manni2
4 Replies

5. Red Hat

how do we check SAN storage?

Hello, I am using LINUX OS. I want to check what is the SAN storage size. How do i check this in server? Any help is really appreciated.. (3 Replies)
Discussion started by: govindts
3 Replies

6. Solaris

Cannot see the IBM SAN storage

HI all, I had recently change the Server storage from EMC to the IBM SAN. but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server. When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies

7. Solaris

SAN Storage for ASM

Hi, We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN. The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes). I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
Discussion started by: esmgr
4 Replies

8. AIX

New to San Storage

Can anyone recommend a good book on san storage basics and how it communicates with an AIX server? (1 Reply)
Discussion started by: NycUnxer
1 Replies

9. Solaris

Connecting to SAN storage - whats need to be done ?

hi all, I am on solaris 10 1/13 and new to SAN storage. I am required to connect to the LUNs on the SAN storage and is asked to provide the WWN information to the storage administrator. Right now, it will be just 1 connection from a single hba port to the FCport on the storage directly,... (1 Reply)
Discussion started by: javanoob
1 Replies
lofi(7D)							      Devices								  lofi(7D)

NAME
lofi - Loopback file driver DESCRIPTION
The lofi file driver exports a file as a block device. Reads and writes to the block device are translated to reads and writes on the underlying file. This is useful when the file contains a file system image. Exporting it as a block device through the lofi file driver allows normal system utilities to operate on the image through the block device (like fstyp(1M)fsck(1M), and mount(1M). This is useful for accessing CD-ROM and FAT floppy images. See lofiadm(1M) for examples. File block device entries are contained in /dev/lofi, while /dev/rlofi contains the character (or raw) device entries. Entries are in the form of decimal numbers which are assigned through lofiadm(1M). When created, these device entries are owned by root, in group sys, and have permissions 0600. While ownership, group, and permission settings can be altered, there are possible ramifications. See lofiadm(1M) for more information. FILES
/dev/lofictl Master control device /dev/lofi/n Block device for file n /dev/rlofi/n Character device for file n /kernel/drv/lofi 32-bit driver /kernel/drv/lofi.conf Driver configuration file. (Should not be altered.) /kernel/drv/sparcv9/lofi 64-bit driver ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsr, SUNWcarx.u | +-----------------------------+-----------------------------+ SEE ALSO
lofiadm(1M), fsck(1M), fstyp(1M), mount(1M), newfs(1M), attributes(5), lofs(7FS) NOTES
Just as you would not directly access a disk device that has mounted file systems, you should not access a file associated with a block device except through the lofi file driver. For compatability purposes, a raw device is also exported along with the block device. For example, newfs(1M) requires one. SunOS 5.10 30 Jul 1999 lofi(7D)
All times are GMT -4. The time now is 05:13 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy