11-08-2010
Thanks for the help, the problem was in a router that modified during my test.
10 More Discussions You Might Find Interesting
1. Solaris
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies
2. Red Hat
Hello,
I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies
3. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
4. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
5. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
6. Linux
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies
7. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
10. Red Hat
I am running apache 2 on centos 7 which is running ipv4 , now I would like to enable it to support ipv6 , would advise what I need to change to Adding IPv6 support to the server ? or nothing need to do ?
the existing vhosts is as below .
<VirtualHost *:80>
ServerAdmin xxx.com.hk
"
"... (2 Replies)
Discussion started by: ust3
2 Replies
LEARN ABOUT OPENSOLARIS
network-admin
network-admin(1) User Commands network-admin(1)
NAME
network-admin - Basic administration of network interfaces.
SYNOPSIS
network-admin [--configure=INTERFACE] [--configure-type=TYPE] [gnome-std-options]
DESCRIPTION
network-admin enumerates the interfaces available to the user and provides a mechanism for configuring these interfaces as static-IP or
DHCP. It's also possible to select which interfaces should be enabled on boot.
network-admin also allows you configure the systems hostname, DNS options and hosts using the user interface.
OPTIONS
The following options are supported:
-c, --configure=INTERFACE Configure a specific network interface (e.g. ath0 or bge0).
-t, --configure-type=TYPE Configure the first network interface of a specific type (e.g. ethernet or wireless).
gnome-std-options Standard options available for use with most GNOME applications. See gnome-std-options(5) for more informa-
tion.
EXAMPLES
Example 1: Running the main application.
example% network-admin
Example 2: Configuring the ath0 network interface.
example% network-admin --configure=ath0
Example 3: Configuring the first ethernet interface.
example% network-admin --configure-type=ethernet
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/network-admin Executable for network interface configuration.
/etc/inet/gnome-system-tools Storage location for network configuration files when not active on boot.
/var/spool/setup-tool-backends/backup/network
Backup directory for files that are modified.
/var/spool/setup-tool-backends/data/network
Where "Location" profiles are stored.
/var/run/setup-tool-backends/debug/network
Debug logs can be found under here.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-system-tools |
+-----------------------------+-----------------------------+
|Interface stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
Latest version of the GNOME Desktop User Guide for your platform.
users-admin(1), shares-admin(1), services-admin(1), time-admin(1), gnome-std-options(5), ifconfig(1M), hosts(4), nsswitch.conf(4),
resolv.conf(4), attributes(5)
NOTES
This tool can only be used to manage physical network devices as returned by the "dladm show-dev" command, it does not support configura-
tion of more complex configurations.
There is currently no support for enterprise name services such as YP/NIS, NIS+ or LDAP. There is also no support for anything but the
global zone.
Written by Darren Kenny, Sun Microsystems Inc., 2006.
SunOS 5.11 6 Nov 2006 network-admin(1)