Sponsored Content
Operating Systems Solaris Solaris 19 10/09 ipv6 interface configuration Post 302469070 by DukeNuke2 on Thursday 4th of November 2010 03:13:50 PM
Old 11-04-2010
read a little further in the admin guide... there should be a part about a file called "/etc/hostname6.<your_nic>".
This User Gave Thanks to DukeNuke2 For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies

2. Red Hat

wireless interface timeout configuration

Hello, I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

5. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies

6. Linux

Help Me: How to set ARP stale time interval on linux platform for Ipv6 interface

Hi, Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ? I have tried increasing the variable gc_stale_time but that doesnt work. Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies

7. IP Networking

IPv6 address block assign/associate with an interface

Hello all, I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack. One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies

8. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

9. Solaris

How to assign IPv4 and IPv6 addresses with same interface?

Hello dears how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies

10. Red Hat

About the apache for ipv6 configuration

I am running apache 2 on centos 7 which is running ipv4 , now I would like to enable it to support ipv6 , would advise what I need to change to Adding IPv6 support to the server ? or nothing need to do ? the existing vhosts is as below . <VirtualHost *:80> ServerAdmin xxx.com.hk " "... (2 Replies)
Discussion started by: ust3
2 Replies
GLOBUS-GATEKEEPER-(8)					       University of Chicago					     GLOBUS-GATEKEEPER-(8)

NAME
globus-gatekeeper-admin - Manage globus-gatekeeper services SYNOPSIS
globus-gatekeeper-admin [-h] globus-gatekeeper-admin [-l] [-n NAME] globus-gatekeeper-admin [-e SERVICE] [-n NAME] globus-gatekeeper-admin [-E] globus-gatekeeper-admin [-d SERVICE] DESCRIPTION
The globus-gatekeeper-admin program manages service entries which are used by the globus-gatekeeper to execute services. Service entries are located in the /etc/grid-services directory. The globus-gatekeeper-admin can list, enable, or disable specific services, or set a service as the default. The -h command-line option shows a brief usage message. Listing services The -l command-line option to globus-gatekeeper-admin will cause it to list all of the services which are available to be run by the globus-gatekeeper. In the output, the service name will be followed by its status in brackets. Possible status strings are ENABLED, DISABLED, and ALIAS to NAME, where NAME is another service name. If the -n NAME is used, then only information about the service named NAME is printed. Enabling services The -e SERVICE command-line option to globus-gatekeeper-admin will cause it to enable a service so that it may be run by the globus-gatekeeper. If the -n NAME option is used as well, then the service will be enabled with the alias NAME. Enabling a default service The -E command-line option to globus-gatekeeper-admin will cause it to enable a service alias with the name jobmanager. The globus-gatekeeper-admin program will choose the first service it finds as the default. To enable a particular service as the default, use the -e parameter described above with the -n parameter. Disabling services The -d SERVICE command-line option to globus-gatekeeper-admin will cause it to disable a service so that it may not be run by the globus-gatekeeper. All aliases to a disabled service are also disabled. FILES
/etc/grid-services Default location of enabled gatekeeper service descriptions. University of Chicago 12/13/2011 GLOBUS-GATEKEEPER-(8)
All times are GMT -4. The time now is 06:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy