|
|
Sponsored Content
Operating Systems
Solaris
Solaris 19 10/09 ipv6 interface configuration
Post 302469069 by pabloluja on Thursday 4th of November 2010 03:09:04 PM
11-04-2010
Solaris 19 10/09 ipv6 interface configuration
Last edited by DukeNuke2; 11-04-2010 at 04:15 PM..
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies
2. Red Hat
Hello,
I have a small desktop running RedHat 5. Depending where I'm at, it connects to the network by a wireless interface or a wired interface. If I'm in an are where there is no wireless network, the box hangs on boot up. It will not timeout and move on. It just hangs. Is there a timeout... (0 Replies)
Discussion started by: garskoci
0 Replies
3. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
4. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
5. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
6. Linux
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies
7. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
10. Red Hat
I am running apache 2 on centos 7 which is running ipv4 , now I would like to enable it to support ipv6 , would advise what I need to change to Adding IPv6 support to the server ? or nothing need to do ?
the existing vhosts is as below .
<VirtualHost *:80>
ServerAdmin xxx.com.hk
"
"... (2 Replies)
Discussion started by: ust3
2 Replies
LEARN ABOUT OPENSOLARIS
protocols
protocols(4) File Formats protocols(4) NAME
protocols - protocol name database SYNOPSIS
/etc/inet/protocols /etc/protocols DESCRIPTION
The protocols file is a local source of information regarding the known protocols used in the DARPA Internet. The protocols file can be used in conjunction with or instead of other protocols sources, including the NIS maps ``protcols.byname'' and "protocols.bynumber" and the NIS+ table ``protocols''. Programs use the getprotobyname(3SOCKET) routine to access this information. The protocols file has one line for each protocol. The line has the following format: official-protocol-name protocol-number aliases Items are separated by any number of blanks and/or TAB characters. A `#' indicates the beginning of a comment; characters up to the end of the line are not interpreted by routines which search the file. Protocol names may contain any printable character other than a field delimiter, NEWLINE, or comment character. EXAMPLES
Example 1 A Sample Database The following is a sample database: # # Internet (IP) protocols # ip 0 IP # internet protocol, pseudo protocol number icmp 1 ICMP # internet control message protocol ggp 3 GGP # gateway-gateway protocol tcp 6 TCP # transmission control protocol egp 8 EGP # exterior gateway protocol pup 12 PUP # PARC universal packet protocol udp 17 UDP # user datagram protocol # # Internet (IPv6) extension headers # hopopt 0 HOPOPT # Hop-by-hop options for IPv6 ipv6 41 IPv6 # IPv6 in IP encapsulation ipv6-route 43 IPv6-Route # Routing header for IPv6 ipv6-frag 44 IPv6-Frag # Fragment header for IPv6 esp 50 ESP # Encap Security Payload for IPv6 ah 51 AH # Authentication Header for IPv6 ipv6-icmp 58 IPv6-ICMP # IPv6 internet control message protocol ipv6-nonxt 59 IPv6-NoNxt # No next header extension header for IPv6 ipv6-opts 60 IPv6-Opts # Destination Options for IPv6 FILES
/etc/nsswitch.conf configuration file for name-service switch SEE ALSO
getprotobyname(3SOCKET), nsswitch.conf(4) NOTES
/etc/inet/protocols is the official SVR4 name of the protocols file. The symbolic link /etc/protocols exists for BSD compatibility. SunOS 5.11 13 Jun 2002 protocols(4)