dhcp status of an interface Post: 302467702

8 More Discussions You Might Find Interesting

1. IP Networking

Solaris Virtual Interface Problem in DHCP

Hi all, I am experiencing a problem with dhcp broadcast packages. these broadcast packages are seen on bge1 and bge1:1 interfaces but somehow they are not seen at bge771001 interface which is second virtual interface on the bge1 interface. I have a server on which I configured it as working...

2. IP Networking

Connecting to DHCP network with Realtek interface

I have a Realtek 8139 interface in one of my machines and it will not connect to the network. /etc/rc.conf contains ifconfig_rl0="DHCP" and "rl0" was obtained from a dmesg. A network interface restart yields the following: # /etc/rc.d/netif restart Stopping network: lo0 rl0 fwe0 plip0. rl0: no...

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

5. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

6. IP Networking

DHCP Server on Vxworks multi interface question

Hi, We currently operate a DHCP Server on Vxworks system. It seems that the server is functioning only over the boot interface. While trying to use it on a different interface the DHCP client messages seems to reach the interface but stay without response. From a...

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

8. IP Networking

Get DHCP relay interfaces IP address using DHCP

Hi All , please view the set up below: ------------------------------------------------------------------- | DHCP Server |-----------| ROUTER & |-----------| Clients | | 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X | ...

LEARN ABOUT OPENSOLARIS

install-solaris

install-solaris(1M)                                                                                                            install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris  invokes  the  Solaris  Install  program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

           Minimum physical memory for all installation types

       128 MB

           Minimum physical memory required for windowing system

       384 MB

           Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

           Minimum physical memory for all installation types

       256 MB

           Minimum physical memory required for windowing system

       512 MB

           Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris  exists  only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE         |      ATTRIBUTE VALUE        |
       +-----------------------------+-----------------------------+
       |Availability                 |SUNWcdrom  (Solaris instal-  |
       |                             |lation media)                |
       +-----------------------------+-----------------------------+
       |Interface Stability          |Evolving                     |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

                                                                    23 Sep 2005                                                install-solaris(1M)