I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk
Put into /etc/hostname.xxx name of the server, then into /etc/hosts file server IP and name, in /etc/defaultgateway gateway IP and in /etc/resolv.conf domain name and IP's od DNS servers.
Then move /etc/nsswitch.dns to /etc/nsswitch.conf and reboot.
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
HI,
I am new to unix. I have used some basic commands and written some simple shell scripts in teh past. Currently, I am supposed to write a script to continuosly check if a couple of machines are up and if not to start a script. I am using a bash - 2.03. I have tryying to use the ping command... (3 Replies)
DEar all
i am receiving this error on start and then unable to ping
(dlpid): unable to open network adapter driver (/dev/mdi/e3h0)
what to do ? (2 Replies)
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Hello,
Am unable to ping the Windows Box, from my Solaris Box.
They both are in same LAN, have the same IP Segments.
Windows IP :: 10.141.14.120
Solaris IP :: 10.141.14.11
Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Hi all,
I have gone through many posts related to this issue,but my issue wasn't resolved hence creating new thread.
I am unable to ping localhost.
ping localhost tries to ping localhost which is defined in DNS.
My /etc/hosts has entry for localhost as
127.0.0.1 loopback localhost.
... (8 Replies)
Hi All,
I am new to solaris environment and we are using Solaris 9
The problem is am unable to ping a particular server from from one of the solaris server
The traceroute also shows only * * * for all the 30 hops
I tried to check all the settings like
1) /etc/hosts -> contains the... (17 Replies)
Discussion started by: Sanjay255
17 Replies
LEARN ABOUT DEBIAN
rping
RPING(1) librdmacm RPING(1)NAME
rping - RDMA CM connection and RDMA ping-pong test.
SYNOPSIS
rping -s [-v] [-V] [-d] [-P] [-a address] [-p port]
[-C message_count] [-S message_size]
rping -c [-v] [-V] [-d] -a address [-p port]
[-C message_count] [-S message_size]
DESCRIPTION
Establishes a reliable RDMA connection between two nodes using the librdmacm, optionally performs RDMA transfers between the nodes, then
disconnects.
OPTIONS -s Run as the server.
-c Run as the client.
-a address
On the server, specifies the network address to bind the connection to. On the client, specifies the server address to connect to.
-p Port number for listening server.
-v Display ping data.
-V Validate ping data.
-d Display debug information.
-C message_count
The number of messages to transfer over each connection. (default infinite)
-S message_size
The size of each message transferred, in bytes. (default 100)
-P Run the server in persistent mode. This allows multiple rping clients to connect to a single server instance. The server will run
until killed.
NOTES
Because this test maps RDMA resources to userspace, users must ensure that they have available system resources and permissions. See the
libibverbs README file for additional details.
SEE ALSO rdma_cm(7), ucmatose(1), udaddy(1), mckey(1)librdmacm 2007-05-15 RPING(1)