I think that the problem here is if you fully name the source file, then that is what the target will be called, from the directory you are connected to. A similar solution to the previous post is to make your local current directory correct first:-
An alternate is to fully specify the files
... but obviously that is more cumbersome.
I hope that this helps.
Robin
Last edited by rbatte1; 10-27-2010 at 04:58 AM..
Reason: Adding code tags (as I have been chastised)
Basically, I like to know how "mget" command work in terms of data/control channels and in terms of request-respond dialogue.
Also, when I try the command as an example below, is it true than for each file to be transferred, there is a new connection establish? (ie. transferred one file,... (5 Replies)
hello,
i was interested in knowing if you can mget or mput a sequence of files:
example- say i have a dir with 1000 files with the same extension e.g. *.sgi,
is there a way to mget only the last 200 files?
i would assume that there is a flag i would use, or something like:
mget... (14 Replies)
Hi All,
I am using mget (mget server.*) through ftp... ... i dont want to overwrite the files in my localmachine if it is already exists... is it possible through ftp ?? any other optios also mos t welcome
Thnks in advance (4 Replies)
Hi all,
I am currently in the process of setting up an FTP server with limited knowledge :p.
I have run into an issue that i need some help with.
Basically i want to be able to download files off another remote server twice a day every day but i want to make sure it only downloads new... (1 Reply)
Hi
I am trying to ftp all the files from a directory in server2 to server1 (both unix) The below code is in server1
ftpfile=/home/anitha/ftptxt
echo cd mydir >>$ftpfile
echo mget *.* >>$ftpfile
cat $ftpfile | ftp -i server2
mydir is a directory in server2 and there are some test files in... (4 Replies)
Hi Friends,
I need to use if then else logic with the mget command.I need to check if {JOURNAL_CODE}*_1_Audit*.txt exists then download it (using mget)and if not then leave it.Same for the {JOURNAL_CODE}*_2_Audit*.txt file.Can you please tell me how can i achive that?
sftp -b -... (3 Replies)
Hi I'm trying to get all files from a directory with a script. So i'm gone paste my script here:
cd /var/www/match_demos/speedgaming/
lftp -u Gudfaren,xxxxx ftp.speedgaming.pro -e cd 89.221.243.11_27500 -e mget *.dem
exit
when i run that i get:
"File name missed. Try `help mget' for more... (2 Replies)
Hi!
I'm a bit of a unix n00b so be gentle! I need to use ftp to download some files. I have the ftp running in a shell script which had been working perfectly last week. I downloaded around 400 files before it broke on friday.
Now whenever I try to run the script, it starts to download... (3 Replies)
I am writing a scritp in which first step is to get some files from a server.
I am using mget to do that.
here is my FTP code ...
HOST="XXX.XXX.com"
28 ftp -inv $HOST <<END &> $FTP_LOG
29 quote USER $USER
30 quote PASS $PASWD
31 cd log
32 prompt off
33 binary
34 mget... (0 Replies)
Discussion started by: shashidhar
0 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)