10-26-2010
I wouldn't recommend to go with fixed settings on both sides, this is yesterday's technology. It is better to use auto negotiation on both sides. For gigabit ethernet, autonegotation is mandatory by the standard anyway.
This User Gave Thanks to hergp For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
2. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
3. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
4. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
pnmcrop(1) General Commands Manual pnmcrop(1)
NAME
pnmcrop - crop a portable anymap
SYNOPSIS
pnmcrop [-white|-black|-sides] [-left] [-right] [-top] [-bottom] [pnmfile]
All options may be abbreviated to their shortest unique prefix or specified with double hyphens.
DESCRIPTION
Reads a PBM, PGM, or PPM image as input. Removes borders that are the background color, and produces the same type of image as output.
If you don't specify otherwise, pnmcrop assumes the background color is whatever color the top left and right corners of the image are and
if they are different colors, something midway between them. You can specify that the background is white or black with the -white and
-black options or make pnmcrop base its guess on all four corners instead of just two with -sides.
By default, pnmcrop chops off any stripe of background color it finds, on all four sides. You can tell pnmcrop to remove only specific
borders with the -left, -right, -top, and -bottom options.
If you want to chop a specific amount off the side of an image, use pnmcut.
If you want to add different borders after removing the existing ones, use pnmcat or pnmcomp.
OPTIONS
-white Take white to be the background color. pnmcrop removes borders which are white.
-black Take black to be the background color. pnmcrop removes borders which are black.
-sides Determine the background color from the colors of the four corners of the input image. pnmcrop removes borders which are of the
background color.
If at least three of the four corners are the same color, pnmcrop takes that as the background color. If not, pnmcrop looks for two
corners of the same color in the following order, taking the first found as the background color: top, left, right, bottom. If all
four corners are different colors, pnmcrop assumes an average of the four colors as the background color.
The -sides option slows pnmcrop down, as it reads the entire image to determine the background color in addition to the up to three
times that it would read it without -sides.
-left Remove any left border.
-right Remove any right border.
-top Remove any top border.
-bottom
Remove any bottom border.
-verbose
Print on Standard Error information about the processing, including exactly how much is being cropped off of which sides.
SEE ALSO
pnmcut(1), pnmfile(1), pnm(5)
AUTHOR
Copyright (C) 1989 by Jef Poskanzer.
18 March 2001 pnmcrop(1)