10-26-2010
you can use the sun trunking software to build trunks/bonds on solaris 9. it's not part of the solaris 9 media and need to be downloaded.
Sun Downloads
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
9. Solaris
Hi all,
Just istalled Solaris 11.
Want to configure network interfaces and got some problems:
#dladm show-phys
#
#dladm show-link
#
If i run ifconfig -a, i am getting 2 lo0 (loopback) interfaces and thats all.
I can't enable interface, can't list it, can't assign IP to it.
Can... (2 Replies)
Discussion started by: nypreH
2 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
REPO(1) General Commands Manual REPO(1)
NAME
Repo - Example of using QuantLib
SYNOPSIS
Repo
DESCRIPTION
Repo is an example of using the QuantLib interest-rate model framework.
Repo values a fixed-coupon bond repurchase (repo). The repurchase agreement example is set up to use the repo rate to do all discounting
(including the underlying bond income). Forward delivery price is also obtained using this repo rate. All this is done by supplying the
FixedCouponBondForward constructor with a flat repo YieldTermStructure.
SEE ALSO
The source code Repo.cpp, BermudanSwaption(1), Bonds(1), CallableBonds(1), CDS(1), ConvertibleBonds(1), DiscreteHedging(1), EquityOp-
tion(1), FittedBondCurve(1), FRA(1), MarketModels(1), Replication(1), SwapValuation(1), the QuantLib documentation and website at
http://quantlib.org.
AUTHORS
The QuantLib Group (see Authors.txt).
This manual page was added by Dirk Eddelbuettel <edd@debian.org>, the Debian GNU/Linux maintainer for QuantLib.
QuantLib 07 Jul 2006 REPO(1)