10-26-2010
you can use the sun trunking software to build trunks/bonds on solaris 9. it's not part of the solaris 9 media and need to be downloaded.
Sun Downloads
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
9. Solaris
Hi all,
Just istalled Solaris 11.
Want to configure network interfaces and got some problems:
#dladm show-phys
#
#dladm show-link
#
If i run ifconfig -a, i am getting 2 lo0 (loopback) interfaces and thats all.
I can't enable interface, can't list it, can't assign IP to it.
Can... (2 Replies)
Discussion started by: nypreH
2 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT DEBIAN
ifenslave-2.6
IFENSLAVE(8) BSD System Manager's Manual IFENSLAVE(8)
NAME
ifenslave -- Attach and detach slave network devices to a bonding device.
SYNOPSIS
ifenslave [-acdfhuvV] [--all-interfaces] [--change-active] [--detach] [--force] [--help] [--usage] [--verbose] [--version] master slave ...
DESCRIPTION
ifenslave is a tool to attach and detach slave network devices to a bonding device. A bonding device will act like a normal Ethernet network
device to the kernel, but will send out the packets via the slave devices using a simple round-robin scheduler. This allows for simple load-
balancing, identical to "channel bonding" or "trunking" techniques used in switches.
The kernel must have support for bonding devices for ifenslave to be useful.
OPTIONS
-a, --all-interfaces
Show information about all interfaces.
-c, --change-active
Change active slave.
-d, --detach
Removes slave interfaces from the bonding device.
-f, --force
Force actions to be taken if one of the specified interfaces appears not to belong to an Ethernet device.
-h, --help
Display a help message and exit.
-u, --usage
Show usage information and exit.
-v, --verbose
Print warning and debug messages.
-V, --version
Show version information and exit.
If not options are given, the default action will be to enslave interfaces.
EXAMPLE
The following example shows how to setup a bonding device and enslave two real Ethernet devices to it:
# modprobe bonding
# ifconfig bond0 192.168.0.1 netmask 255.255.0.0
# ifenslave bond0 eth0 eth1
AUTHOR
ifenslave was originally written by Donald Becker <becker@cesdis.gsfc.nasa.gov>, and has since been updated by various kernel developers.
This manual page was written by Guus Sliepen <guus@debian.org> for the Debian GNU/Linux system.
Debian GNU/Linux June 1, 2019 Debian GNU/Linux