10-25-2010
I would like to run a collector script.
Its possible to open a root shell to the offline node with the command from the online node?
I have found a command but its only run a SMIT on the offline node, not more. :S
That would be fine if I can logon to the offline node, and run the script, and the results should be back to the online node
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi folks,
I'm a bit of a novice at this but here goes. I want to read in nodes from an XML file, and map the path to each.
eg the file is structured
<node><nodename>.</nodename>
<node><nodename>topnode</nodename>
<node><nodename>subnode1</nodename></node>
... (1 Reply)
Discussion started by: mark14
1 Replies
2. Shell Programming and Scripting
Dear all,
I am bit confused lately, I have a xmlfile here:
file: book.xml
<?xml version="1.0" encoding="ISO-8859-1"?>
<bookstore>
<book category="COOKING">
<title lang="en">Everyday Italian</title>
<author>Giada De Laurentiis</author>
<year>2005</year>
... (2 Replies)
Discussion started by: penyu
2 Replies
3. AIX
Hi all,
I was wondering if someone direct me in how to Make system backup for 2 nodes HACMP cluster ( system image ) .
What are the consideration for this task (3 Replies)
Discussion started by: h@foorsa.biz
3 Replies
4. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
5. Programming
I am new in Linux and clustering. I am setting up a Beowulf Cluster using several PCs according to this guide "Beowulf How-To"
I have setup and configure accordingly except for NFS part. Because I am not requiring it for my application. I have set my ssh to login each other without password. I... (1 Reply)
Discussion started by: nsw1216
1 Replies
6. AIX
As i have updated a lot of HACMP-nodes lately the question arises how to do it with minimal downtime. Of course it is easily possible to have a downtime and do the version update during this. In the best of worlds you always get the downtime you need - unfortunately we have yet to find this best of... (4 Replies)
Discussion started by: bakunin
4 Replies
7. AIX
Hi,
A customer I'm supporting once upon a time broke their 2 cluster node database servers so they could use the 2nd standby node for something else. Now sometime later they want to bring the 2nd node back into the cluster for resilance. Problem is there are now 3 VG's that have been set-up... (1 Reply)
Discussion started by: elcounto
1 Replies
8. Shell Programming and Scripting
Hello to all,
I'd like to tabulate the content of the XML file below, I've been trying with AWK putting the Top node (<KIND>) as RS and so far I'm able to print the first and second field of each record, but I don't know how to continue with the following nodes that have more inner nodes.
The... (4 Replies)
Discussion started by: Ophiuchus
4 Replies
9. Shell Programming and Scripting
Hi
This is my first post to this site.:D
I want to develop a script with following steps:
1.Script1,2,3 placed at particular path on local server
2.ask for an IP and will directly pick up the correct script matching to the IP (IP could be defined in same script or a new script could be called).... (10 Replies)
Discussion started by: veronica
10 Replies
10. AIX
HI Admin,
I have running 2 node HACMP cluster- AIX 6.1. I just set it up.
It does sync completely without any errors. But it take too long to sync. More than 30 mins... any reasons? Where can I start looking into ?
Same network, same Subnet (1 Reply)
Discussion started by: snchaudhari2
1 Replies
load(8) System Manager's Manual load(8)
Name
load - down-line load software to a target node
Syntax
/etc/load [ node ]
Description
The command loads software to an unattended target node. The target node is loaded by the host that executes the command.
The command requires the identification of the service circuit over which the load is performed, the Ethernet hardware address of the tar-
get node, and the service password needed to gain access to the target. This information is included in the nodes database entry for the
target node. A node entry is defined with the command. For further information, see The node is the name or address of the target node.
A node name consists of from one to six alphanumeric characters. For single networks, a node address consists of a decimal integer
(1-1023). For multiple networks, a node address consist of two decimal integers (n.n), where the first indicates the network number
(1-63), and the second indicates the node address (1-1023).
Options
-p Uses the specified service and password (next arguments) in accessing the target node. You can omit a target node's service and pass-
word from the nodes database for security reasons, but you must then specify the service and password in the command line by using the
option.
Examples
# /etc/load bangor -p 130fe
This command causes node to be loaded by the ULTRIX host node executing the command. The ULTRIX host uses the load files specified in the
nodes database entry for node to perform the load.
See Also
addnode(8), ccr(8), getnode(8), mop_mom(8), remnode(8), trigger(8)
Guide to Local Area Transport Servers
load(8)