I think that you need to run something like:
on the DOS machine, or just add 192.168.0.1 as the default gateway.
Where this is added though will depend on the TCP software that you are using.
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Hi,
For one of my application(Linux 2.6) I am using a netlink socket to get the interface changes notification.
socket(PF_NETLINK, SOCK_RAW, NETLINK_ROUTE)
Application receives netlink notification for Ethernet, bond interfaces but there is no notification about bridge interfaces changes. ... (6 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hi
Had an old ML590 with RS232 serial card that stopped working (spindle that advance ribbon broke) so I purchased a working used on ebay.
Printer powers up and seems fine. Put serial board from old printer in working ebay unit but no printing happens.
Does anyone know if there are any... (0 Replies)
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
Hi Folks,
Here is one for the real Solaris aficionados on the site;
I have a T5240 and have to create an I/O domain with access to the serial port, in this case /dev/term/a and although I have been through the documentation I'm having some issues in identifying the device to assign.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT DEBIAN
vde_l3
VDE_L3(1) General Commands Manual VDE_L3(1)NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch.
SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket]
DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup
for each -v option given at command line. Static routes to target networks can be defined using the -r option.
vde_l3 -v /var/run/s1.ctl:192.168.0.1/24
connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0.
vde_l3
-v /var/run/s1.ctl:192.168.0.1/24
-v /var/run/s2.ctl:10.0.0.254/255.255.0.0
connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in
each network can specify the vde_l3 as their gateway to reach the other one.
OPTIONS -v vde_plug:ipaddress/netmask
Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can
be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One
can define as many interfaces as she wants.
-r target_network/netmask:gateway
Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she
wants.
-G default_gw
Specify a default gateway, to be used whenever no static route is defined for a target host.
-M mgmt_socket
the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be
used as a remote terminal for wirefilter.
NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik"
i.e. the German "Association for Electrical, Electronic & Information Technologies").
SEE ALSO vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1).
AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net>
VDE is a project by Renzo Davoli <renzo@cs.unibo.it>
Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)