Need a bridge from an ethernet interface to a serial interface
This is my situation
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
I need the DOS pc can reach the router at 192.168.0.1 and the Internet, so i tried to make a bridge between sl0 and eth1
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Hi,
For one of my application(Linux 2.6) I am using a netlink socket to get the interface changes notification.
socket(PF_NETLINK, SOCK_RAW, NETLINK_ROUTE)
Application receives netlink notification for Ethernet, bond interfaces but there is no notification about bridge interfaces changes. ... (6 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hi
Had an old ML590 with RS232 serial card that stopped working (spindle that advance ribbon broke) so I purchased a working used on ebay.
Printer powers up and seems fine. Put serial board from old printer in working ebay unit but no printing happens.
Does anyone know if there are any... (0 Replies)
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
Hi Folks,
Here is one for the real Solaris aficionados on the site;
I have a T5240 and have to create an I/O domain with access to the serial port, in this case /dev/term/a and although I have been through the documentation I'm having some issues in identifying the device to assign.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT DEBIAN
arpsend
arpsend(8) Containers arpsend(8)NAME
arpsend - send ARP requests
SYNOPSIS
arpsend -D -e target_ip [ -e target_ip ...] [-c count] [-w timeout] interface
arpsend -U -i source_ip [-c count] [-w timeout] interface
DESCRIPTION
Utility arpsend sends ARP packets on device interface to detect or update neighbours' ARP caches with a given IP.
COMMANDS
Run utility with one of the following commands:
-D Send broadcast ARP request to detect neighbours with target_ip. You have to specify target_ip (-e option).
-U Send broadcast ARP request to update neighbours' ARP caches with source_ip. You have to specify source_ip (-i option).
OPTIONS -c count
Number of packets to send. Default is infinity.
-w interval
Interval between packets, in seconds. Default is 1 second.
-i source_ip_address
Set source IP address field in ARP packet.
-e target_ip_address
Set target IP address field in ARP packet. Note that you can specify -e option multiple times to detect many IP addresses in one
utility call.
EXIT STATUS
arpsend returns 0 upon successful execution. If something goes wrong, it returns an appropriate error code.
1 EXC_USAGE
Usage error
2 EXC_SYSTEM
System error
3 EXC_RECV
ARP reply was received
EXAMPLES
To send request on interface eth0 to detect any neighbour computers with IP 192.168.10.200:
arpsend -D -e 192.168.10.200 eth0
To send request on interface eth0 to update neighbours' ARP caches with IP 192.168.10.200:
arpsend -U -i 192.168.10.200 eth0
NOTES
Interface you use have to be arpable and not be loopback (i.e. /sbin/ip link show interface should show neither NOARP nor LOOPBACK flags
in interface parameters).
SEE ALSO vzctl(8).
LICENSE
Copyright (C) 2000-2011, Parallels, Inc. Licensed under GNU GPL.
OpenVZ 28 Jun 2011 arpsend(8)