Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT MOJAVE
locale::codes::langfam5.18
Locale::Codes::LangFam(3pm) Perl Programmers Reference Guide Locale::Codes::LangFam(3pm)NAME
Locale::Codes::LangFam - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangFam;
$lext = code2langfam('apa'); # $lext gets 'Apache languages'
$code = langfam2code('Apache languages'); # $code gets 'apa'
@codes = all_langfam_codes();
@names = all_langfam_names();
DESCRIPTION
The "Locale::Codes::LangFam" module provides access to standard codes used for identifying language families, such as those as defined in
ISO 639-5.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 639-5
language family codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language families. A code set may be specified using either a name, or a
constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langfam('apa','alpha');
$lext = code2langfam('apa',LOCALE_LANGFAM_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from ISO 639-5 such as 'apa' for Apache languages.
This is the default code set.
ROUTINES
code2langfam ( CODE [,CODESET] )
langfam2code ( NAME [,CODESET] )
langfam_code2code ( CODE ,CODESET ,CODESET2 )
all_langfam_codes ( [CODESET] )
all_langfam_names ( [CODESET] )
Locale::Codes::LangFam::rename_langfam ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangFam::add_langfam ( CODE ,NAME [,CODESET] )
Locale::Codes::LangFam::delete_langfam ( CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_alias ( NAME ,NEW_NAME )
Locale::Codes::LangFam::delete_langfam_alias ( NAME )
Locale::Codes::LangFam::rename_langfam_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::delete_langfam_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.loc.gov/standards/iso639-5/id.php
ISO 639-5 .
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangFam(3pm)