10-19-2010
Lsof will tell you where it connected, and if routing is doing the interface selection, you can traceroute the IP to ensure that is working. I am not that often able to play with lsof, but it may tell you enough about the connection. Also, the backup stats should change little or none until you start backup.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
7. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT CENTOS
backup_help
BACKUP_HELP(8) AFS Command Reference BACKUP_HELP(8)
NAME
backup_help - Displays help for backup commands
SYNOPSIS
backup help [-topic <help string>+] [-admin] [-help]
backup h [-t <help string>+] [-a] [-h]
DESCRIPTION
The backup help command displays the complete online help entry (short description and syntax statement) for each operation code specified
by the -topic argument. If the -topic argument is omitted, the output includes the first line (name and short description) of the online
help entry for every backup command.
To list every backup command whose name or short description includes a specified keyword, use the backup apropos command.
OPTIONS
-topic <help string>+
Indicates each command for which to display the complete online help entry. Omit the backup part of the command name, providing only
the operation code (for example, specify dump, not backup dump). If this argument is omitted, the output briefly describes every backup
command.
-help
Prints the online help for this command. All other valid options are ignored.
OUTPUT
The online help entry for each backup command consists of the following two or three lines:
o The first line names the command and briefly describes its function.
o The second line lists aliases for the command, if any.
o The final line, which begins with the string "Usage", lists the command's options in the prescribed order. Online help entries use the
same symbols (for example, brackets) as the reference pages in this document.
EXAMPLES
The following example displays the online help entry for the backup dump command:
% backup help dump
backup dump: start dump
Usage: backup dump -volumeset <volume set name> -dump <dump level name>
[-portoffset <TC port offset>] [-at <Date/time to start dump>+]
[-append] [-n] [-file <load file>] [-help]
PRIVILEGE REQUIRED
None
SEE ALSO
backup(8), backup_apropos(8)
COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved.
This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas
Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell.
OpenAFS 2012-03-26 BACKUP_HELP(8)