10-19-2010
Lsof will tell you where it connected, and if routing is doing the interface selection, you can traceroute the IP to ensure that is working. I am not that often able to play with lsof, but it may tell you enough about the connection. Also, the backup stats should change little or none until you start backup.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
5. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
6. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
7. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT DEBIAN
svn-fast-backup
svn-fast-backup(1) General Commands Manual svn-fast-backup(1)
NAME
svn-fast-backup - very fast backup for Subversion fsfs repositories.
SYNOPSIS
svn-fast-backup [-q] [-k{N|all}] [-f] [-t] [-s] repos_path backup_dir
DESCRIPTION
svn-fast-backup uses rsync snapshots for very fast backup of a Subversion fsfs repository at repos_path to backup_dir/repos-rev, the latest
revision number in the repository. Multiple fsfs backups share data via hardlinks, so old backups are almost free, since a newer revision
of a repository is almost a complete superset of an older revision.
This is good for replacing incremental log-dump+restore-style backups because it is just as space-conserving and even faster; there is no
inter-backup state (old backups are essentially caches); each backup directory is self-contained. It has the same command-line interface
as svn-hot-backup(1) (if you use --force), but only works for fsfs repositories.
svn-fast-backup keeps 64 backups by default and deletes backups older than these; this can be adjusted with the -k option.
OPTIONS
-h, --help
Shows some brief help text.
-q, --quiet
Quieter-than-usual operation.
-k, --keep=N
Keep a specified number of backups; the default is to keep 64.
-k, --keep=all
Do not delete any old backups at all.
-f, --force
Make a new backup even if one with the current revision exists.
-t, --trace
Show actions.
-s, --simulate
Don't perform actions.
AUTHOR
Voluntary contributions made by many individuals. Copyright (C) 2006 CollabNet.
2006-11-09 svn-fast-backup(1)