10-18-2010
Run something like his script earlier or one time, and have it leave the results for each somewhere accessible to your script?
10 More Discussions You Might Find Interesting
1. IP Networking
What is the significance of the broadcast address? (1 Reply)
Discussion started by: 98_1LE
1 Replies
2. Shell Programming and Scripting
Dear all,
This is the Bionic Fysh again. I have two quick questions:
1- when writing shell scripts, how does one allow the tilda ~ into the script ?
e.g
ls ~;
ls ~me;
user=you;
ls ~$user (N.B I think that for this one you need: ls `~$user`)
2- In FreeBSD 4.0, I would like for a... (6 Replies)
Discussion started by: bionicfysh
6 Replies
3. UNIX for Dummies Questions & Answers
say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on?
And could you explain how to get the answer?
thanx in advance! (7 Replies)
Discussion started by: pnxi
7 Replies
4. Solaris
I have a bge1 card and a bge0 card, i want the broadcast addresses to match, ifconfig shows this
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
... (1 Reply)
Discussion started by: csaunders
1 Replies
5. Shell Programming and Scripting
hi all...
I am executing a comman in a shell script but the command needs a user input of character 'y' as input so it stops in between...may i know is there is any way of giving that character as input in the shell script itself???...thanks in advance.... (6 Replies)
Discussion started by: santy
6 Replies
6. Shell Programming and Scripting
Hi,
I want to send input to promt from shell script, this thing is possible.
I give the one command
`/usr/share/ssl/misc/CA -newreq`
it needs some user input like password etc., but i need this input also from shell script but it does not works.
`/usr/share/ssl/misc/CA -newreq` <<EOF... (2 Replies)
Discussion started by: Vaibhav Agarwal
2 Replies
7. Shell Programming and Scripting
Hi
Suppose
You have two computers. One named kenny which has an IP address of 192.168.0.7. kenny lives
on a subnet with a subnet mask of 255.255.255.240. The second computer is called zathras, which
has an IP address of 192.168.0.17, zathras lives on a network with the same subnet mask.
i)... (4 Replies)
Discussion started by: scofiled83
4 Replies
8. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
9. Programming
My problem definition is ,I have to send a message from one node in a network and it has to be broadcasted to all other nodes in the network.The program what I have given below will be running in all the nodes in the network.The same program should be capable of sending(broadcasting) and receiving.... (1 Reply)
Discussion started by: vigneshinbox
1 Replies
10. Shell Programming and Scripting
Hi folks
I need to write UNIX script (with ldapsearch) to query Active Directory. Input is NT login name and output is Email address.
Attached a screenshot of Sysinternals "AD Explorer". I need to do the same in CLI.
http://i.imgur.com/4s6FB.png
I am absolute LDAP/ldapsearch noob. (0 Replies)
Discussion started by: slashdotweenie
0 Replies
LEARN ABOUT DEBIAN
dist::zilla::plugin::run
Dist::Zilla::Plugin::Run(3pm) User Contributed Perl Documentation Dist::Zilla::Plugin::Run(3pm)
NAME
Dist::Zilla::Plugin::Run - Run external commands at specific phases of Dist::Zilla
VERSION
version 0.013
SYNOPSIS
[Run::BeforeRelease]
run = script/myapp_before1.pl %s
run = script/myapp_before2.pl %n %v
[Run::Release]
run = script/myapp_deploy1.pl %s
run = deployer.pl --dir %d --tgz %a --name %n --version %v
[Run::AfterRelease]
run = script/myapp_after.pl %s %v
; %p can be used as the path separator if you have contributors on a different OS
run = script%pmyapp_after.pl %s %v
DESCRIPTION
Run arbitrary commands at various Dist::Zilla phases.
CONVERSIONS
The following conversions/format specifiers are defined for passing as arguments to the specified commands (though not all values are
available at all phases).
o %a the archive of the release (available to all *Release phases)
o %d the directory in which the dist was built (not in "BeforeBuild")
o %n the dist name
o %p path separator ('/' on Unix, '\' on Win32... useful for cross-platform dist.ini files)
o %v the dist version
o %x full path to the current perl interpreter (like $^X but from Config)
Additionally %s is retained for backward compatibility. Each occurrence is replaced by a different value (like the regular "sprintf"
function). Individual plugins define their own values for the positional replacement of %s.
AUTHOR
Torsten Raudssus <torsten@raudssus.de> <http://www.raudssus.de/>
COPYRIGHT AND LICENSE
This software is copyright (c) 2010 by Raudssus Social Software <http://www.raudssus.de/>.
This is free software; you can redistribute it and/or modify it under the same terms as the Perl 5 programming language system itself.
perl v5.12.4 2011-11-09 Dist::Zilla::Plugin::Run(3pm)