10-18-2010
i deleted the results because it can be confidential to state.
But ethernet adapters were available on both.
Last edited by lordofdarkness; 10-18-2010 at 07:41 AM..
Reason: may be confidential info
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies
2. Solaris
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Discussion started by: jeelans
1 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies
5. IP Networking
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
Discussion started by: Katkota
3 Replies
6. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
7. AIX
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies
8. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
9. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
10. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)