10-18-2010
i deleted the results because it can be confidential to state.
But ethernet adapters were available on both.
Last edited by lordofdarkness; 10-18-2010 at 07:41 AM..
Reason: may be confidential info
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies
2. Solaris
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Discussion started by: jeelans
1 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies
5. IP Networking
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
Discussion started by: Katkota
3 Replies
6. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
7. AIX
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies
8. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
9. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
10. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT DEBIAN
massagevendor
MASSAGEVENDOR(8) System Manager's Manual MASSAGEVENDOR(8)
NAME
massagevendor - convert the ethernet vendor codes master list to arpwatch format
SYNOPSIS
massagevendor vendorfile
DESCRIPTION
massagevendor is a program that converts a text file containing ethernet vendor codes into a format suitable for use by arpwatch(8) and
arpsnmp(8). The input vendorfile is a master text file containing vendor codes. The output is sent to stdout. Each line of the vendorfile
is expected to have a six digit hexadecimal vendor code followed by spaces followed by the name of the manufacturer.
All ethernet devices have a unique identifier which includes a vendor code specifying the manufacturer of the device. In normal operation
arpwatch(8) and arpsnmp(8) use the file ethercodes.dat to report this vendor code. massagevendor is used to generate the ethercodes.dat
file from text files containing these vendor codes.
Locations where an ethernet vendor codes master text file can be obtained are given below.
FILES
/usr/share/arpwatch - default location of the ethernet vendor list
ethercodes.dat - file containing the list of ethernet vendor codes
SEE ALSO
arpwatch(8), arpsnmp(8)
NOTES
Sources for ethernet vendor codes seen in the wild are
http://map-ne.com/Ethernet/vendor.html
ftp://ftp.cavebear.com/pub/Ethernet.txt
http://www.cavebear.com/CaveBear/Ethernet/vendor.html
Useful for comparison or completeness are the
ethernet vendor codes as assigned
by the IEEE which can be found at
http://standards.ieee.org/regauth/oui/oui.txt
BUGS
Please send bug reports to arpwatch@ee.lbl.gov.
AUTHORS
Craig Leres of the Lawrence Berkeley National Laboratory Network Research Group, University of California, Berkeley, CA.
The current version is available via anonymous ftp:
ftp://ftp.ee.lbl.gov/arpwatch.tar.gz
This manual page was contributed by Hugo Graumann.
MASSAGEVENDOR(8)