10-17-2010
Well, I just want to create a snapshot of an existing zone. I want to be able to roll back if needed. Are you telling me there is no way to snapshot this pool?
6 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
Discussion started by: fulhamfcboy
1 Replies
2. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
3. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
4. Solaris
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies
5. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
6. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT DEBIAN
snapconv
snapconv(1) Emulators snapconv(1)
NAME
snapconv - Sinclair ZX Spectrum snapshot converter
SYNOPSIS
snapconv [ -c ] [ -n ] infile outfile
DESCRIPTION
snapconv converts between ZX Spectrum snapshot files.
OPTIONS
-c specifies that all data in the output snapshot should be compressed, even if that compression will result in a bigger file than if
some data is left uncompressed. This helps compatibility with some buggy programs that can only read entirely compressed .z80 files.
-n specifies that the output snapshot should be uncompressed.
-f specifies that the A and F and A' and F' registers should be swapped. Version 0.5.0 and older of libspectrum(3) had a bug that
resulted in these registers being swapped in SZX snapshots only. Version 0.5.1 and newer of libspectrum(3) automatically recognise
these snapshots and correct the problem, but this flag is necessary to fix some snapshots created by development versions only of
libspectrum(3) which had the bug fixed, but cannot be distinguished from snapshots containing the bug.
infile specifies the snapshot to be converted. This file can be in any of the snapshot formats supported by libspectrum(3).
outfile
specifies the output snapshot. The format will be determined by the file extension and can be in any of the formats libspectrum(3)
supports for output.
BUGS
None known.
SEE ALSO
fuse(1), fuse-utils(1), libspectrum(3), listbasic(1), snap2tzx(1)
The comp.sys.sinclair Spectrum FAQ, at
http://www.worldofspectrum.org/faq/index.html.
AUTHOR
Philip Kendall (philip-fuse@shadowmagic.org.uk).
Version 1.0.0 16th December, 2010 snapconv(1)