AWK break string into fields + pattern match Post: 302462607

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

how can awk match multi pattern in a string

Hi all, I need to category the processes in my system with awk. And for now, there are several command with similar name, so i have to match more than one pattern to pick it out. for instance: binrundb the string1, 2 & 3 may contain word, number, blank or "/". The "bin" should be ahead "rundb"...

2. Shell Programming and Scripting

AWK match $1 $2 pattern in file 1 to $1 $2 pattern in file2

Hi, I have 2 files that I have modified to basically match each other, however I want to determine what (if any) line in file 1 does not exist in file 2. I need to match column $1 and $2 as a single string in file1 to $1 and $2 in file2 as these two columns create a match. I'm stuck in an AWK...

3. Shell Programming and Scripting

pattern match in a string

Hello, Please see below line code: #!/bin/ksh set -x /usr/bin/cat /home/temp |while read line do if ] then echo "matched" else echo "nope" fi done content of filr temp is as below

4. Shell Programming and Scripting

Awk to match a pattern and perform a search after the first pattern

Hello Guyz I have been following this forum for a while and the solutions provided are super useful. I currently have a scenario where i need to search for a pattern and start searching by keeping the first pattern as a baseline ABC DEF LMN EFG HIJ LMN OPQ In the above text i need to...

5. Shell Programming and Scripting

awk : match only the pattern string , not letters or numbers after that.

Hi Experts, I am finding difficulty to get exact match: file OPERATING_SYSTEM=HP-UX LOOPBACK_ADDRESS=127.0.0.1 INTERFACE_NAME="lan3" IP_ADDRESS="10.53.52.241" SUBNET_MASK="255.255.255.192" BROADCAST_ADDRESS="" INTERFACE_STATE="" DHCP_ENABLE=0 INTERFACE_NAME="lan3:1"...

6. Shell Programming and Scripting

Pattern Match and Rearrange the Fields in UNIX

For an Output like below Input : <Subject A="I" B="1039502" C="2015-06-30" D="010101010101"> Output : <Subject D="010101010101" B="1039502" C="2015-06-30" A="I"> I have been using something like below but not getting the desired output : awk -F ' ' '/Subject/ BEGIN{OFS=" ";}...

7. Shell Programming and Scripting

awk partial string match and add specific fields

Trying to combine strings that are a partial match to another in $1 (usually below it). If a match is found than the $2 value is added to the $2 value of the match and the $3 value is added to the $3 value of the match. I am not sure how to do this and need some expert help. Thank you :). file ...

8. UNIX for Beginners Questions & Answers

awk script for pattern match and line break

Hi, I have input which reads like 9089.00 ----- kl jkjjljk lkkk; (909099) 9097.00 ----- HGJJHHJ jcxkjlkjvhvlk jhdkjksdfkhfskd 898.00 ----- HHHH I am trying to do something like this - As soon as I found pattern match "XYZ.00-----" it will insert a line break to the input and will go to...

9. Shell Programming and Scripting

awk to print match or non-match and select fields/patterns for non-matches

In the awk below I am trying to output those lines that Match between file1 and file2, those Missing in file1, and those missing in file2. Using each $1,$2,$4,$5 value as a key to match on, that is if those 4 fields are found in both files the match, but if those 4 fields are not found then missing...

10. UNIX for Beginners Questions & Answers

awk match two fields in two files

Hi, I have two TEST files t.xyz and a.xyz which have three columns each. a.xyz have more rows than t.xyz. I will like to output rows at which $1 and $2 of t.xyz match $1 and $2 of a.xyz. Total number of output rows should be equal to that of t.xyz. It works fine, but when I apply it to large...

LEARN ABOUT DEBIAN

svn-bisect

SVN-BISECT(1)						      General Commands Manual						     SVN-BISECT(1)

NAME

       svn-bisect - Bisect Subversion revisions to find a regression

SYNOPSIS

       svn-bisect start [good_rev [bad_rev]]

       svn-bisect {good|bad} [rev]

       svn-bisect run command

       svn-bisect reset

       svn-bisect status

DESCRIPTION

       svn-bisect  helps  to  automate	finding a bug or behavior change in a Subversion working copy.	Given an initial "good" revision, with the
       desired or original behavior, and a newer "bad" revision, with the undesired or modified behavior,  svn-bisect  will  do  a  binary  search
       through the revision range to find which revision caused the change.

       svn-bisect  must  be initialized in a working copy, with svn-bisect start.  It also needs to be given at least one good revision (the base-
       line) and one bad revision (known modified behavior) revision.

       Sub-commands:

       start  Initializes or reinitializes svn-bisect; optionally takes good and bad revision parameters.

       good rev

       bad rev
	      Tells svn-bisect that a revision is good or bad, defining or narrowing the search space.	If not specified, revision defaults to the
	      current  revision  in  the working copy.	svn-bisect will then update to a revision halfway between the new good and bad boundaries.
	      If this update crosses a point where a branch was created, it switches in or out of the branch.

       reset  Resets the working copy to the revision and branch where svn-bisect start was run.  In the simple case this is equivalent to  rm	-r
	      .svn-bisect;  svn  update,  but  not  if	it  has crossed branches, and not if you did not start at the HEAD revision.  In any case,
	      svn-bisect never keeps track of mixed-revision working copies, so do not use svn-bisect in a working  copy  that	will  need  to	be
	      restored to mixed revisions.

       status Prints a brief status message.

       run command
	      Runs  the  bisection in a loop.  You must have already defined initial good and bad boundary conditions.	Each iteration through the
	      loop runs command as a shell command (a single argument, quoted if necessary) on the chosen revision, then  marks  the  revision	as
	      good or bad, based on the exit status of command.

EXAMPLES

       Assume you are trying to find which revision between 1250 and 1400 caused the make check command to fail.

	   svn-bisect start 1250 1400
	   svn-bisect run 'make check'
	   svn-bisect reset

ENVIRONMENT

       SVN    The Subversion command-line program to call (default svn).

FILES

       .svn-bisect
	      The directory containing state information, removed after a successful bisection.

SEE ALSO

       git-bisect(1).

AUTHOR

       Written by Robert Millan and Peter Samuelson, for the Debian Project (but may be used by others).

								    2009-10-22							     SVN-BISECT(1)