10-13-2010
I have a intel video driver
.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello
(Very New to UNIX -Solaris 10)
I'm trying to set the LANG variable to C but not sure if it's getting set, need some help on this.
Currently I have it set to en_GB.UTF-8
I need to set it to C for an install. but when I run set LANG=C and then run echo $LANG its still set to... (2 Replies)
Discussion started by: deedaz
2 Replies
2. AIX
Hi Guys,
Can somebody help me how to add and activate addtional ip address on AIX.
My server is IBM p5-570
i already set ipadress on ent1
ent0 -- 192.168.206.105 ( default )
ent1 -- 192.168.0.89 (additional)
i can ping from outside to 192.168.0.89 but i can not telnet or ftp.
for... (6 Replies)
Discussion started by: cahyo3074
6 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I am trying to set up a dual boot system with Red Hat EL 5.2 and Windows XP Pro. I have a separate disk for each OS. Grub is on the same disk as redhat(the primary disk). I know that Windows is installed correctly because if I force a load on the secondary disk Windows loads correctly.... (0 Replies)
Discussion started by: adawg1217
0 Replies
4. UNIX Desktop Questions & Answers
I want to setup dual monitor for the Dell Optiplex Gx520 computer.
The motherboard has an Intel Corporation 82915G Integrated Graphics
Controller.
Then I add an ATI Rage 128 video card.
The dual monitor work on Windows 2000 with the Intel chip as the
primary screen and the ATI chip... (0 Replies)
Discussion started by: TsanChung
0 Replies
5. Linux
Hi,
To simplify things, the name of the pc's are 'spectra1' and 'spectra3'. Spectra3 already has dual screen, and I'm trying to connect and 2nd screen for spectra1. I went to System Settings > Display > Dual head tab: on spectra1 and enabled the "use dual head" then clicked Configue...
From... (0 Replies)
Discussion started by: shamrocks
0 Replies
6. Infrastructure Monitoring
dears, any one knows how to use linux command to monitor hp server Redhat dual power status? any 1 of power failure then alarm will triggered. (4 Replies)
Discussion started by: maxlee24
4 Replies
7. Solaris
Hello!
I have some X86 desktop computer with G45 embedded dual-head video.
Two monitors can be configured, but with "small" problem: the summ of dimensions in any direction (vert or horis) can't exceed 1680 pix- max sizeof virtual screen area.
Attempts to edit "videoram" parameter in xorg.conf... (0 Replies)
Discussion started by: urry_buh
0 Replies
8. Hardware
Hi,
I would like to ask if someone has knowlodge or perhaps own/experience this kind of a machine, Im buying a desktop with a plan of having multiple monitor 3 or 4,now my question is, i want to used the sli or crossfire config with each video card has 2 dvi or vga connector, does this 2... (0 Replies)
Discussion started by: jao_madn
0 Replies
9. Hardware
Hi, I am experiencing troubles with dual monitors in fedora 16. During boot time both monitors are working, but when system starts one monitor automatically shut down. It happend out of the blue. Some time before when I updated system this happend but then I booted older kernel release and... (0 Replies)
Discussion started by: wakatana
0 Replies
10. Infrastructure Monitoring
Sorry if this is the wrong forum
Searching for Saas Monitor service which monitor my servers which are sitting in different providers .
This monitor tool will take as less CPU as possible , and will send info about the server to main Dashboard.
The info I need is CPU / RAM / my servers status (... (1 Reply)
Discussion started by: umen
1 Replies
LEARN ABOUT OPENSOLARIS
mpt
MPT(4) BSD Kernel Interfaces Manual MPT(4)
NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device mpt
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mpt_load="YES"
DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers.
HARDWARE
The following controllers are supported by the mpt driver:
o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI)
o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA)
o LSI Logic FC909 (1Gb/s Fibre Channel)
o LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel)
o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel)
o LSI Logic FC949X (Dual 4Gb/s Fibre Channel)
o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express)
The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including:
o Dell PowerEdge 1750 thru 2850
o IBM eServer xSeries 335
These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports.
The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both
SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at
best.
The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the
FC949ES card.
This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the
LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required.
SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8)
LSI Logic Website, http://www.lsilogic.com/.
HISTORY
The mpt driver first appeared in FreeBSD 4.6.
AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>.
Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements.
BUGS
BSD
May 13, 2010 BSD