10-13-2010
Quote:
Originally Posted by
DukeNuke2
so ignore the messages... looks like a known error with oracle installed.
Thanks for your answer.
Is that messages related with FO cable or SAN Switch?
Best Regards
Wisnu
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello,
Need to know all benefits\differences for V890 over V880.
We are really keen to know about this.
Can anybody please take out some time and get us the information.
Regards,
Narinder (4 Replies)
Discussion started by: narinderd
4 Replies
2. Solaris
I am trying to use a flash image to install a v890.
I have the image on another box.
I am trying to use ftp to pull down the image.
But, when i go though the install, choose flash, enter the ftp info, it can not ever connect to the server.
I've never had this trouble before.
There are 4... (4 Replies)
Discussion started by: BG_JrAdmin
4 Replies
3. Solaris
Question, I have a new V890 preloaded witrh Solaris 10. Due to SW compatibility I need to run Sol 8 on the server. When running boot cdrom from the ok prompt, I get amessages looking for a location on the CDROM to find the startup install SW. The path must be different from what's on Sol 10 install... (4 Replies)
Discussion started by: stocksj
4 Replies
4. UNIX for Advanced & Expert Users
I have worked with Qlogic (Sun) fiber cards a lot and with Emulex fiber cards only a little. Here is the scenario: I have a Sun 490 with 3 Emulex cards in it. A pair are for the 6120 array that is attached, the other is a direct attach so our SAN for Veritas Netbackup to back up the system.I... (0 Replies)
Discussion started by: lm_admin_dh
0 Replies
5. Solaris
Hello Experts,
I have a StorEdge 3320 attached to V890, the problem is that I am copying data from v890's internal hdds to 3320's hdds, it is taking a-lot of time, the transfer is very slow.
while I have checked the transfer from V890's internal hdd to another machines it is good. So, its mean... (15 Replies)
Discussion started by: bluetooth
15 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. Hardware
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
8. Solaris
I just received a v890. I cannot get it to boot via CDROM nor can I access the SC prompt because I do not know the password. I am attempting to access it via serial cable to a Linux box.
What is the best way to proceed? (25 Replies)
Discussion started by: LittleLebowski
25 Replies
9. Solaris
I am battling to get a V890 up and running. The system appears to have AUTOBOOT=false, so no OS comes up when it's powered on, and I do not have the credentials to get to the RSC management console. Output to ttya serial console ends at "Probing I/O buses", I assume because output is then being... (4 Replies)
Discussion started by: dstmark
4 Replies
10. Solaris
Hi all
I am currently using a T5120 to write and run some simulation code I've been working on which heavily relies on large matrix multiplication procedures. I am posting this to call out for some of you run and share the results of a simple benchmark I've written to compare the matrix... (1 Reply)
Discussion started by: toguro123
1 Replies
LEARN ABOUT HPUX
st_san_safe
st_san_safe(5) OBSOLETED st_san_safe(5)
NAME
st_san_safe - determine whether access to tape device special files without the no-rewind-on-close option is allowed (OBSOLETED)
VALUES
Failsafe
Default
Allowed values
Recommended values
or
DESCRIPTION
Note: this tunable is obsoleted and has been renamed to beginning with release HP-UX 11i v3.
This tunable notifies the tape driver whether it should allow access to device special files without the no-rewind-on-close option. When
this tunable is on the tape driver will fail any open on a tape device special file without the no-rewind-on-close option (that is, or with
a status of
The tunable allows the safe sharing of tape devices in SAN tape backup solution configurations. The disabling of device special files
without no-rewind-on-close in a SAN tape backup solution configuration prevents the accidental sending of a rewind command on close from
HP-UX systems via standard tape commands like which would corrupt a backup in process.
Who Is Expected to Change This Tunable?
Anyone.
Restrictions on Changing
Changes to this tunable take effect immediately.
When Should the Tunable Be Turned On?
This tunable should be turned on if the system is going to be used in a SAN tape backup solution configuration.
What Are the Side Effects of Turning the Tunable On?
The tape driver will fail any open to a tape device special file that does not have the no-rewind-on-close option with a status of This
behavior prevents the usage of any tape device special file without the no-rewind-on-close option.
When Should the Tunable Be Turned Off?
This tunable should be turned off if the system is not part of a SAN tape backup solution configuration or the system utilizes will not
function unless it has access to device special files without the no-rewind-on-close option.
What Are the Side Effects of Turning the Tunable Off?
A rewind may be issued from this system accidentally on close possibly corrupting a backup being issued from another system on the SAN.
What Other Tunables Should Be Changed at the Same Time?
None.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by Hewlett-Packard.
SEE ALSO
norewind_close_disabled(5), scsi_tape(7), scsimgr_estape(7).
Tunable Kernel Parameters st_san_safe(5)