10-12-2010
Network Problem
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of the lpars can ping the gateway. I have the same problem in vio02. I use only one physical network adapter and created shared ethernet adapter for lpars with same VLAN ID. Is there any limitations to use same shared ethernet? If yes how can i solve this problem? If not what can be the problem?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies
2. Solaris
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Discussion started by: jeelans
1 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies
5. IP Networking
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
Discussion started by: Katkota
3 Replies
6. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
7. AIX
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies
8. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
9. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
10. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT REDHAT
vconfig
VCONFIG(8) System Manager's Manual VCONFIG(8)
NAME
vconfig - VLAN (802.1q) configuration program.
SYNOPSIS
vconfig [lots of long options]
DESCRIPTION
The vconfig program allows you to create and remove vlan-devices on a vlan enabled kernel. Vlan-devices are virtual ethernet devices which
represents the virtual lans on the physical lan.
OPTIONS
add [interface-name] [vlan-id]
Creates a vlan-device on [interface-name]. The resulting vlan-device will be called according to the nameing convention set.
rem [vlan-device]
Removes the named vlan-device.
set_flag [vlan-device] 0 | 1
When 1, ethernet header reorders are turned on. Dumping the device will appear as a common ethernet device without vlans. When
0(default) however, ethernet headers are not reordered, which results in vlan tagged packets when dumping the device. Usually the
default gives no problems, but some packet filtering programs might have problems with it.
set_egress_map [vlan-device] [skb-priority] [vlan-qos]
This flags that outbound packets with a particular skb-priority should be tagged with the particular vlan priority vlan-qos. The
default vlan priority is 0.
set_ingress_map [vlan-device] [skb-priority] [vlan-qos]
This flags that inbound packets with the particular vlan priority vlan-qos should be queued with a particular skb-priority. The
default skb-priority is 0.
set_name_type VLAN_PLUS_VID | VLAN_PLUS_VID_NO_PAD | DEV_PLUS_VID | DEV_PLUS_VID_NO_PAD
Sets the way vlan-device names are created. Use vconfig without arguments to see the different formats.
NOTES VLAN will use Broadcom's NICE interface when the network device supports it. This is necessary, since usually the hardware of these
devices already removes the vlan tag from the ethernet packet. The set_flag option on vlan-devices created on such a physical net-
work device will be ignored. Dumping the network-device will show only untagged(non-vlan) traffic, and dumping the vlan-devices
will only show traffic intended for that vlan, without the tags.
FILES
/proc/net/vlan/config
/proc/net/vlan/[vlan-device]
SEE ALSO
ip(8), ifconfig(8)
AUTHORS
This manual page was written by Ard van Breemen <ard@kwaak.net>
The vlan patch is written by Ben Greear <greearb@candelatech.com>
VCONFIG(8)