Network interface problem Post: 302461681

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

2. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same...

3. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error...

4. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:...

5. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

7. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

8. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT MOJAVE

uname

UNAME(1)						    BSD General Commands Manual 						  UNAME(1)

NAME

     uname -- Print operating system name

SYNOPSIS

     uname [-amnprsv]

DESCRIPTION

     The uname utility writes symbols representing one or more system characteristics to the standard output.

     The following options are available:

     -a      Behave as though all of the options -mnrsv were specified.

     -m      print the machine hardware name.

     -n      print the nodename (the nodename may be a name that the system is known by to a communications network).

     -p      print the machine processor architecture name.

     -r      print the operating system release.

     -s      print the operating system name.

     -v      print the operating system version.

     If no options are specified, uname prints the operating system name as if the -s option had been specified.

SEE ALSO

     hostname(1), machine(1), sw_vers(1), uname(3)

STANDARDS

     The uname utility conforms to IEEE Std 1003.2-1992 (``POSIX.2'').	The -p option is an extension to the standard.

BSD
								 November 9, 1998							       BSD

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

network interface problem

Discussion started by: sc2005

2. Solaris

network interface problem solaris 2.5

Discussion started by: kroegand

3. AIX

Problem with a Network Interface

Discussion started by: aldowsary

4. UNIX for Dummies Questions & Answers

Multi Network card interface problem

Discussion started by: sarifudin