Network interface problem Post: 302461679

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

2. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same...

3. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error...

4. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:...

5. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

7. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

8. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT OPENSOLARIS

amd8111s

amd8111s(7D)							      Devices							      amd8111s(7D)

NAME

       amd8111s - AMD-8111 Fast Ethernet Network Adapter driver

SYNOPSIS

       /dev/amd8111s

DESCRIPTION

       The  amd8111s  Fast Ethernet driver is a multi-threaded, loadable, clonable,  GLD-based	STREAMS  driver supporting  the Data Link Provider
       Interface, dlpi(7P), on the AMD-8111 Fast Ethernet Network Adapter.

       The amd8111s driver functions include controller initialization, frame  transmit and receive, promiscuous and multicast support, and  error
       recovery and reporting.

APPLICATION PROGRAMMING INTERFACE

       The cloning, character-special device /dev/amd8111 is used to access all AMD-8111 Fast Ethernet devices installed within the system.

       The  amd8111s  driver  is managed by the dladm(1M) command  line utility, which allows VLANs to be defined on top of amd8111s instances and
       for amd8111s instances to be aggregated.  See dladm(1M) for more details.

CONFIGURATION

       By default, the amd8111s driver performs auto-negotiation to select the link speed and mode. Link speed and mode can be any of the  follow-
       ing:

       100 Mbps, full-duplex.

       100 Mbps, half-duplex.

       10 Mbps, full-duplex.

       10 Mbps, half-duplex.

FILES

       /dev/amd8111s*

	   Special character device.

       /kernel/drv/amd8111s*

	   32-bit ELF kernel module (x86).

       /kernel/drv/amd64/amd8111s*

	   64-bit ELF Kernel module (x86).

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------------------------------------+
       |ATTRIBUTE TYPE		      ATTRIBUTE VALUE		   |
       |Availability		      SUNW8111s 		   |
       |Architecture		      x86			   |
       |Interface Stability	      Committed 		   |
       +-----------------------------------------------------------+

SEE ALSO

       dladm(1M), attributes(5), streamio(7I), dlpi(7P)

       Writing Device Drivers

       STREAMS Programming Guide

       Network Interfaces Programmer's Guide

 SunOS 5.11							    30 Jul 2007 						      amd8111s(7D)

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

network interface problem

Discussion started by: sc2005

2. Solaris

network interface problem solaris 2.5

Discussion started by: kroegand

3. AIX

Problem with a Network Interface

Discussion started by: aldowsary

4. UNIX for Dummies Questions & Answers

Multi Network card interface problem

Discussion started by: sarifudin